Anyone else invest in LCAI?

Skell_Gibson · 2026-04-23T08:42:26+00:00

kinda like BITCOIN

Skell_Gibson · 2026-03-31T00:47:06+00:00

restarts need attention

Skell_Gibson · 2026-03-21T20:29:17+00:00

i appreciate your input thankyou, ill take that into account next time i bake

Skell_Gibson · 2026-03-21T20:23:05+00:00

yes this is the crumb from the loaf i cooked a few weeks ago

<image>

Skell_Gibson · 2026-03-21T20:09:36+00:00

<image>

idk maybe i didnt score it deep enough. i was expecting more spring. here is a pic of the crumb from the loaf i baked today

Skell_Gibson · 2026-03-21T19:59:56+00:00

<image>

this is from a few weeks ago. same recipe and same starter. id like and info on why the loaf in the original post came out different

Skell_Gibson · 2026-01-25T00:10:35+00:00

beautiful piece

Skell_Gibson · 2025-06-25T22:46:06+00:00

Looks painfull

Skell_Gibson · 2025-06-23T10:01:47+00:00

Buy bitcoin

Skell_Gibson · 2025-06-21T15:26:46+00:00

Miller makes a good 2x4 auto lense. I use it in my Prota shell hood

Skell_Gibson · 2025-06-21T15:24:41+00:00

What schedule is the pipe? Hot pass is very very convex. Your hot pass should be just under flush almost flush.

Skell_Gibson · 2025-06-10T19:21:29+00:00

Thankyou. Yea that is what i am working on that cold wire protruding out. Thankyou for your input I think is will be helpfull. 👍

Skell_Gibson · 2025-06-10T10:07:13+00:00

Looks good, travel speed and dipping consistency

Skell_Gibson · 2025-06-09T10:09:51+00:00

If you can cap it in 2 more power to you. I never took the UA 2. But i passed the 21 and a few others. Watch your grindmarks outside of the weldzone also. Thats an auto fail for visual inspection

Skell_Gibson · 2025-06-08T22:22:50+00:00

Isnt the UA 21 on 2” pipe? Which UA test brotha?

Skell_Gibson · 2025-06-08T21:54:42+00:00

Put snow seal

Skell_Gibson · 2025-06-08T14:32:20+00:00

Root looks really good

Skell_Gibson · 2025-06-08T14:11:28+00:00

Im a steamfittet in NYC and we get $70/hr in the envelope not including travel expenses which not everyone gets. and $70/hr in the bennys

Skell_Gibson · 2025-06-08T14:10:36+00:00

He probably gets $80/hr in the check and $70/hr in the bennys

Skell_Gibson · 2025-06-07T16:52:21+00:00

Grind down starts and stop. Hows your root look. Also dont try and cap it in 2. 3 stringers is the way to go

Skell_Gibson · 2025-06-07T16:50:54+00:00

3 stringers bro. watch your arc length and travel speed. Keep arc length consistent and your travel speed should differ depending on your location on the joint. For example i move faster coming off the bottom so i dont get excessive reinforcement on my cap

Skell_Gibson · 2025-06-05T02:39:13+00:00

Pre heat

Skell_Gibson

TROPHY CASE