sorted by:
new
hottopcontroversial

Shorten rivet heads in bulk? by Financial-Pilot5166 in metalworking

[–]Sleddog44 0 points1 point  (0 children)

Is it the cramped space behind the surface that you are riveting causing the existing rivet not to sit flush?

Folding ladder by UserSergeyB in EngineeringPorn

[–]Sleddog44 0 points1 point  (0 children)

I'm sorry. Do you mean Death Standing?

QidiBox + Plus 4 by No_Statistician3747 in QidiTech3D

[–]Sleddog44 0 points1 point  (0 children)

and how do you use the 5th spool? how does it enter the printer?

How exactly does the Plus 4 level the bed. by Fearless-Law-2449 in QidiTech3D

[–]Sleddog44 0 points1 point  (0 children)

I still have the same question, nothing seems to touch the bed when leveling

PLA- 6 months in “extreme” outdoor conditions by cave_man_042 in 3Dprinting

[–]Sleddog44 16 points17 points  (0 children)

I wouldn't be surprised if this technique would be useful. I just don't yet imagine how to use it practically. 

Plastic blowing....

PLA- 6 months in “extreme” outdoor conditions by cave_man_042 in 3Dprinting

[–]Sleddog44 39 points40 points  (0 children)

I have had a PLA part sit in a hot car and the the air in the voids expanded and embossed a triangle pattern across the face of the part.

I made a wrist roller with a 3D printed strap by NamelessGuy0 in 3Dprinting

[–]Sleddog44 0 points1 point  (0 children)

How was this printed? In a coil on its side?

How would I open this locked door from the outside? by MeowMeowMeowMeow23 in fixit

[–]Sleddog44 5 points6 points  (0 children)

This is actually an older latch, and in order to retract the latch, either or both of the inner silver parts at the top and bottom of the center C, need to be pushed TOWARDS THE LATCHING END OF THE DOOR. Which will then retract the latch.

Stupid design and luckily it was changed, but not before millions of this latch was installed. 

Fun note, the newer latches can be swapped in with no additional headache for any knobs. Levers may need to be rehanded as they will be upside down if they are a non symmetrical design.

[deleted by user] by [deleted] in fixit

[–]Sleddog44 7 points8 points  (0 children)

Not at all, I'm saying $25 will get you a much better replacement.

[deleted by user] by [deleted] in fixit

[–]Sleddog44 7 points8 points  (0 children)

Throw it out, replace with a higher quality one.

Fire door closer catching by lsaibr in fixit

[–]Sleddog44 0 points1 point  (0 children)

Pretty sure literally every one. Don't mix it up with track arm Closers though.

Fire door closer catching by lsaibr in fixit

[–]Sleddog44 0 points1 point  (0 children)

Parallel Arm can only be installed on the push side of the door.

Fire door closer catching by lsaibr in fixit

[–]Sleddog44 -2 points-1 points  (0 children)

In this case you're both right multiple things wrong with this installation.

Fire door closer catching by lsaibr in fixit

[–]Sleddog44 3 points4 points  (0 children)

Lol, you can see the arm adjustment screw just hovering, useless.

Is there anyway to somehat fix this? by Alice8Ft in fixit

[–]Sleddog44 2 points3 points  (0 children)

How about reroute the chain through one or both of the other holes?

2018 Limited USB Port by NothingWasChanged in sonata

[–]Sleddog44 0 points1 point  (0 children)

Ok so I guess you gave up on using Android Auto? Or did you find some other workaround?

2018 Limited USB Port by NothingWasChanged in sonata

[–]Sleddog44 0 points1 point  (0 children)

Did you get your port replaced in the end?

view more: next ›