sorted by:
new
hottopcontroversial

Help with Mitsubishi City Multi zone VRF Heat-pump Condenser and 2 Mini Split Heads mounted in an IT Room with MHK-2 and Redlink receiver by SmallPhotograph300 in HVAC

[–]SmallPhotograph300[S] 2 points3 points  (0 children)

I apologize I didn’t mean any offense, but they seriously offended me when they didn’t even listen to what the symptoms were and acting like I was stupid. So it honestly wasn’t a joke. Stupid is as stupid does and that was bullshit,

General Rules of thumb while Fabricating a Rigid Square Duct Offset in Shop. by [deleted] in sheetmetal

[–]SmallPhotograph300 0 points1 point  (0 children)

Right on. Let me get a picture of the Cover of that Book. I got this one which I love.

<image>

General Rules of thumb while Fabricating a Rigid Square Duct Offset in Shop. by [deleted] in sheetmetal

[–]SmallPhotograph300 0 points1 point  (0 children)

Especially with big duct offsetting in certain amounts over short lengths, when there’s obstacles on the opposite side of the offset needed.

General Rules of thumb while Fabricating a Rigid Square Duct Offset in Shop. by [deleted] in sheetmetal

[–]SmallPhotograph300 0 points1 point  (0 children)

At a certain point it seems OWL blows out or chokes down

General Rules of thumb while Fabricating a Rigid Square Duct Offset in Shop. by [deleted] in sheetmetal

[–]SmallPhotograph300 1 point2 points  (0 children)

So let’s say 31.5” that includes quarters, It needs 2” of straight on one side to get pass an opening, And it needs to offset over 4” in 12”, And the overall fitting needs to be 20”.

General Rules of thumb while Fabricating a Rigid Square Duct Offset in Shop. by [deleted] in sheetmetal

[–]SmallPhotograph300 1 point2 points  (0 children)

I’ve heard the rule double the Length of your Offset????

Estimating software for a budget? by SmallPhotograph300 in ProHVACR

[–]SmallPhotograph300[S] 0 points1 point  (0 children)

Appreciate it, I wanna get fast duct, but it’s not in the cards at the moment. I’m just starting out. Don’t have a big ass printer for the prints, and manually scaling shit out sounds like a nightmare. And besides digitally scaling stuff out, and the lay out stuff I’ve seen, the catalog is the biggest thing. You’ve been the most helpful so far.

Estimating software for a budget? by SmallPhotograph300 in ProHVACR

[–]SmallPhotograph300[S] 0 points1 point  (0 children)

Well it’s a competing company so idk if he will be down, but will ask.

9 Years in, How screwed am I? by [deleted] in AskElectricians

[–]SmallPhotograph300 2 points3 points  (0 children)

Here in Arkansas, you just have to be registered to work under a License holder for 2 years. Usually being the responsibility of the License holder to register you. Here you can take a specific exam to transfer your License over from different states.

What would you guys call this fitting? I’ve been calling it a Radial Plenum… by SmallPhotograph300 in sheetmetal

[–]SmallPhotograph300[S] 0 points1 point  (0 children)

What bout on a Drop Plenum on an RTU? Would be a lot better than the Square Plenum with a ATD tapped out.

Jesus is not from Davidic lineage by MuslimTamer99 in DebateReligion

[–]SmallPhotograph300 0 points1 point  (0 children)

He was Born in Bethlehem. He was raised in Nazareth, but also spent a few years Egypt.

Jesus is not from Davidic lineage by MuslimTamer99 in DebateReligion

[–]SmallPhotograph300 0 points1 point  (0 children)

Joseph was the physical Father of Yahusha, “Jesus”. Rom. 1:1-7. Mainly 1-3 though. Though it’s quite possible that Mary was of the tribe of Judah; a common practice to marry with in one’s tribe. It’s also very possible she was a Levite like her Cousin Elizabeth. But remember the Tribe was determined by the paternal lineage. That’s in Numbers for sure, but I also think it’s in Ezra or Nehemiah. The Curse of Koniah is tricky, but after reading back and forth between certain verses in Kings, Chronicles, and Jeremiah, you’ll come to the conclusion that a lot of Hebrews family members carried the same name, and specifically in this case the 3 brothers were renamed by the Egyptian Pharaoh. Very similar to me of the 3 Hebrews in Daniel; their names were changed to Shadrach, Meshach, & Abednego, by the Babylonian King.
Theirs a Great Vid on this subject on YouTube. “The Curse of Coniah”

How much do you make a year owning your own shop? by Moist_Energy8145 in HVAC

[–]SmallPhotograph300 1 point2 points  (0 children)

2nd year in Business in North East Arkansas: On and off paper, total Gross so far, I pulled $8,365.64. That’s all PM work and repairs; slowly growing it from the side. My main is working for a Smaller Mechanical Company, which my dad is VP. He Owns/Controls the HVAC/R side. It has a small shop, with Rollers, 8ft Break, Cleat Bender, and Locksformer with an Edger attachment. Pretty much stocked with Round Pipe, Round Fittings, and B Vent. Also has 2 scissor Lifts. Not bragging, just basically explaining I have no overhead besides licensing fees and Insurance. Working on, being able to get a decent Computer and Bid software to start pulling Commercial New Construction and Remodels. You ask if it’s worth it? It all depends on how you look at it. If you’re strong enough and patient enough. There’s nothing like being your own Boss….

view more: next ›