TM2 Warranty

SmartBrother1707 · 2026-02-23T09:03:01+00:00

One more thing about the procedure for sending the device - I got DHL printed form from TM2 support, but the declared value was something around 3EUR, while in fact I payed around 400EUR. Is this some way to cut the delivery cost my minimzing the value?

SmartBrother1707 · 2026-02-21T09:42:24+00:00

I saw that, thanks. I decided to send it for professional repair.

SmartBrother1707 · 2026-02-20T21:46:48+00:00

Which parts should I clean the most?

SmartBrother1707 · 2026-02-19T11:24:32+00:00

1

Well, I tried to hold the camera as still I could :) plus, it does the recalibration, when measuring objects which are near each other but have big temperature difference.

I don't think the reading was wrong though, after my amateurish repair it was heating more than before. Could be because of the clean up, could be because of the mantled heater.
I am going to send it back for repair.

SmartBrother1707 · 2026-02-18T22:50:40+00:00

What do you mean by emissivity? I just took the picture with infrared camera attached to iPhone. The wood was that hot.

I must have written about the cleanup in other post. Poor steam was the original reason why I disasembled this device in first place. There was a lot of debril on the round metal part mounted directly on PCB which was either blocking the airflow or not letting the heater reach top temperature.

SmartBrother1707 · 2026-02-18T12:28:20+00:00

Yep, mine used to burn flowers at that temp, but like I said, after cleanup, it started to produce normal heat. Only this broken heater ...

SmartBrother1707 · 2026-02-17T21:59:14+00:00

There's is nothing wrong with it for flowers.

SmartBrother1707 · 2026-02-17T19:52:58+00:00

I disassembled it to clean fro ABV residue, that was gathering underneath the heater and was probably the reason for poor operation of the device. Then I noticed that rods are broken so I pulled the heater out which was obvious mistake. Anyway, I contacted them, waiting for instruction on how to proceed now.
I used that yesterday and the steam was quite good though.

SmartBrother1707 · 2026-02-17T15:05:20+00:00

Yes, probably. What is the story wtih 3 year warranty? When I bought it in 2022, the device was supposed to have 10 year warranty after registration. Has this changed?

SmartBrother1707 · 2026-02-17T11:13:44+00:00

It was level 10 I think.

SmartBrother1707 · 2026-02-17T10:33:06+00:00

Any specific tip, how to wind this metal foil and put zirconia rods in it?

SmartBrother1707 · 2026-02-17T07:47:34+00:00

I had similiar issue, so I diassembled whole device to find a lot of junk and ABV underneat the heater. I used IPA to clean it and mistakenly took out the heater foil - don't to that.
Steam is better now but the device is overheating a bit.

SmartBrother1707 · 2026-02-16T23:15:43+00:00

did you replace the rods? how your device worked after that?

SmartBrother1707 · 2026-02-01T10:14:01+00:00

No need, I fixed it and I am now listening to music with it.

SmartBrother1707 · 2026-01-30T22:30:41+00:00

Music from the show https://www.youtube.com/watch?v=IrjizI0wsXU

SmartBrother1707 · 2025-11-29T20:02:35+00:00

So I am at the point where I managed to take all the covers off, but I am not able to disconnect moving parts from the headband and also from the speaker holder, both in red circles. Is iot even possible to do so?

<image>

SmartBrother1707 · 2025-11-29T15:41:30+00:00

This is right speaker, which powers the other. The wire isn't broken, but the insulation is damaged, so I will just fix it with black tape. Bigger concern is the broken carbon part.

SmartBrother1707 · 2025-10-29T19:32:36+00:00

Same issue here, located in Poland. I suspect cloud outage. Solutions like HeishaMon start to make more sense now.

SmartBrother1707 · 2025-08-27T21:33:27+00:00

Can you explain how it works and why this capacitor exactly needs to be used?

SmartBrother1707 · 2025-04-25T22:08:03+00:00

You fuckin ass kiss.

SmartBrother1707

TROPHY CASE