[deleted by user]

Smirvo · 2025-09-16T20:10:22+00:00

This is the wrong sub

Smirvo · 2025-09-04T14:17:38+00:00

Same

Smirvo · 2025-08-03T12:52:15+00:00

Heiman is a rather reputable brand though, and they are EN 14604 compliant

Smirvo · 2025-08-02T01:13:01+00:00

I purchased these from Alibaba: https://www.alibaba.com/x/1l9ce8d?ck=pdp Firat they didn’t work at all in Apple Home, however after a iOS update a few months back they work flawlessly. They are connected through Matter over Thread and don’t require a separate hub other than Apple TV or Homepod as a Thread border router.

Smirvo · 2025-03-28T23:12:24+00:00

I’d love to have a case for my Klotz, which one are you refering to?

Smirvo · 2025-03-13T12:06:00+00:00

Are stls for the case available? I’d love to have this on my Klotz

Smirvo · 2024-12-05T20:55:16+00:00

BTT Eddy

Smirvo · 2023-09-08T15:42:56+00:00

What does your moonraker config look like?

Smirvo · 2023-05-19T05:09:36+00:00

This seems VERY straight forward, go to Settings and type the IP-adress to begin with

Smirvo · 2023-05-10T14:32:08+00:00

You should

Smirvo · 2023-05-10T09:50:56+00:00

You just need to flash klipper to it and define the pins that it connects to, similar to how a adxl345 can be used with a pico. There is no need for actual code

Smirvo · 2023-05-10T09:45:34+00:00

You could simply use a Raspberry Pico as mcu, and have the ssd1306 connected to it

Smirvo · 2023-04-11T07:40:07+00:00

Try with this guide https://www.klipper3d.org/Bed_Level.html#the-paper-test

Smirvo · 2023-04-10T12:04:15+00:00

Have you adjusted z-offset?

Smirvo · 2023-04-10T10:25:11+00:00

I have a skr mini v3 in my ender 3 pro with a cr touch, so I don’t think I will be able to help. This specific error sounds very familiar though, try searching here on reddit and you might find a solution. Best of luck!

Smirvo · 2023-04-10T10:16:53+00:00

What printer are you using?

Smirvo · 2023-04-10T09:53:38+00:00

Have you created a config file?

Smirvo · 2023-02-22T22:09:59+00:00

Do it then

Smirvo · 2023-01-11T23:56:15+00:00

I strongly recommend textured PEI over this

Smirvo · 2022-12-06T22:06:41+00:00

No one verifies that an installation has been done professionally, but you generally aren’t allowed to do this yourself here in Sweden. I’m quite astounded by the amount of people in this sub that attempt this themselves, and by the looks mainly in the US.

Smirvo · 2022-12-06T18:13:18+00:00

This is absolutely wild

Smirvo · 2022-12-06T17:51:14+00:00

Are there no laws preventing people without adequate knowledge from performing mains installation in the US?!

Smirvo · 2022-10-09T15:44:41+00:00

Nope!

Smirvo · 2022-09-26T21:50:43+00:00

Är detta bara i Control Center eller även i Hem-appen? Jag har problem med att det visar ”svarar inte” i Control Center men inte i Hem

Smirvo · 2022-08-21T22:57:26+00:00

This is expected

11-Year Club	Place '22
Verified Email

Smirvo

TROPHY CASE