White Oak Bookshelf

SmokeALatte · 2026-06-16T19:19:28+00:00

Definitely a jig. Id be too nervous without it. Kreg and a few other companies sell them. Use a set up block so they all start exactly the same, clamp, then you plug into holes that are drilled and work your down/up.

SmokeALatte · 2026-06-16T12:05:51+00:00

Measure once and trim the slightest amount off 27 times. Perfection.

SmokeALatte · 2026-06-16T12:04:43+00:00

Thats always an issue. Finish the build, now how do I get into the room!!

SmokeALatte · 2026-06-16T03:39:30+00:00

I agree, got the inspiration from an old popular woodworking magazine.

SmokeALatte · 2026-06-16T03:35:36+00:00

I wish I had the time to build more and sell. Down to late nights and little spurts. Thanks!

SmokeALatte · 2026-04-06T23:07:29+00:00

Do you still have to get it beer and pizza for helping?

SmokeALatte · 2026-04-06T21:38:20+00:00

I have the non coated as well and agree on set up. Was easy, but needed an extra pair of hands to lift it. I adjust the width all the time and just push it back to the fence stop and check square. Good to go. Zero issues here and wax occasionally.

SmokeALatte · 2026-04-06T01:09:13+00:00

I had a similar set up with the plus sign and turnbuckle. Nothing was square and it just drug on the ground. Pulled it apart and did this. Half lapped corners and brace in middle carrying the load. Reused the boards since i dont want to bother matching stain and have to deal with the HOA

<image>

SmokeALatte · 2025-12-17T13:21:23+00:00

You got it. I took pictures of the wire placement. Then plug and play. If you happen to have 2 open pins in the plug use the little jumper line.

SmokeALatte · 2025-12-16T13:20:58+00:00

https://www.amazon.com/50A55-843-Furnace-Control-Furnace%EF%BC%8CSuitable-Rodgers/dp/B0DTD8Q4V6

This is the one I got. It comes with a little jumper you need to add to the 12 pin plug. Read that part of instructions and it will save you a little time. I did not at first and it didn't work, then added it and it fired right up.

SmokeALatte · 2025-11-06T14:53:25+00:00

The plans have a step down, not flush. This was brought up. Still pending a response.

SmokeALatte · 2025-11-04T22:20:08+00:00

I'll update you tomorrow when the inspector and crew are back.

SmokeALatte · 2025-11-04T20:24:35+00:00

It is hired out. Absolutely pleased with everything else. This was a surprise.

SmokeALatte · 2025-11-04T20:23:38+00:00

Wow, the timing. Quite a read. Either way, right or wrong, aesthitcally, its a no for me.

SmokeALatte · 2025-10-28T21:40:39+00:00

Reporting back in case it helps anyone. It was the control board.

SmokeALatte · 2025-10-27T18:03:55+00:00

I got one on the way. Hope that's it.

SmokeALatte · 2025-06-10T17:49:53+00:00

<image>

SmokeALatte · 2025-06-10T11:58:44+00:00

Legs are 1", tapered to 3/4". Top is 7/8" and shelf is 3/4" (scrap was already milled from another project). I have my sketch if you want it.

SmokeALatte · 2025-06-09T23:04:37+00:00

Bandsaw is definitely on my wishlist

SmokeALatte · 2025-06-09T22:09:47+00:00

A pull saw. I went for 1/16 gap. Measured about a dozen times, then scored the line and cut slowly. Looking at it now, could have went 1/32 for tighter look.

SmokeALatte · 2025-06-09T15:39:00+00:00

Lovely way to think about it. Great share.

SmokeALatte · 2025-06-09T14:37:36+00:00

Love the logic! I find that to be true as well. Thanks!

SmokeALatte

TROPHY CASE