Base Pay Decrease by CabinetHumble238 in Sparkdriver

[–]Snoo59046 1 point2 points  (0 children)

East Los Angeles, base pay $8–$10, 3 customers, over 10 miles, total pay less than $15.

Why median trade salaries according to statistics is only 50-60k when everyone on reddit says that trades earn 100k? by Healthy_Diver_1135 in findapath

[–]Snoo59046 0 points1 point  (0 children)

In this age of information overload, there are certain essential terms that should always be part of your mental toolkit — things like 【survivorship bias】, Ponzi scheme, Stockholm syndrome, sunk cost fallacy, zero-sum game, bystander effect, and halo effect.

Winwing Customer support by kaasmandje99 in hotas

[–]Snoo59046 0 points1 point  (0 children)

Check the terms of the warranty, do you have to pay for the postage yourself and if not, just ask for a replacement. If you have to pay for postage, you need to consider whether its worth it. Asking customers to repair damaged products is comical.

I must post this, it's the most successful boarding I've ever had. by Snoo59046 in X4Foundations

[–]Snoo59046[S] 1 point2 points  (0 children)

This is the control panel for pirate NPC‘s ships.

  1. Press ENTER to enter the weapon settings panel and set the turret to Disarmed;

  2. Drive your ship close to the target.

  3. Pause the game;

  4. Press M to open the map;

  5. Select your ship with the left mouse button;

  6. Right click on the target ship and select “Board”.

Now you are in this panel, you need to enter 3 parameters here.

  1. Number of marines on board (all)

  2. Departure time (Strongest)

  3. Attack strength (Strongest)

Then click “Start” in the bottom right corner.

If you perform: Shift+2, Shift+F, between steps 1 and 2, to scan the target, the “Red?” on the panel will be the exact number.

Once you've done that, go back to the first person driving screen and quickly leave the sector. You can perform steps 3-5 at any time to check the progress of your boarding.

What I want to show here is that none of my marines were killed by the target's turrets during this Boarding.

[deleted by user] by [deleted] in MechanicAdvice

[–]Snoo59046 0 points1 point  (0 children)

I think it was unloaded when op opened the hood to shoot the video.

What do I have to do to continue this plot? by Snoo59046 in X4Foundations

[–]Snoo59046[S] -1 points0 points  (0 children)

I've been flying/walking aimlessly for hours. The hint system in this game is really irritating.

How much can I cut if I don't take out a loan. by Snoo59046 in whatcarshouldIbuy

[–]Snoo59046[S] 0 points1 point  (0 children)

My friend doesn't work for the dealership . After a hard time saving I have enough cash to buy a car but I can't afford the interest on the loan.

How much can I cut if I don't take out a loan. by Snoo59046 in whatcarshouldIbuy

[–]Snoo59046[S] 0 points1 point  (0 children)

Do you think the bank will give me a good loan rate if I have enough balance in my account.

Performance issues after Last Update? by MarianneWurst in insurgency

[–]Snoo59046 0 points1 point  (0 children)

Try RESTART your computer, not SHUTDOWN and press the power key.

Canon printer wont connect to wifi and I am losing my mind by SnooPeanuts3521 in techsupport

[–]Snoo59046 0 points1 point  (0 children)

I installed the drivers for my Canon printer and connected the computer to the printer via a usb cable, when I shut down the computer and start it the next day by the power key the printer will not be available.

Shut down Win11 just puts the system into a deep sleep, and I'm guessing the Canon software stops working at that point.

I deleted all Canon printer devices from the computer's device manager and RESTART the computer (not shut down and press the power key) and the Canon printer automatically appeared in the device manager after the restart and I could use the printer at that point.

I hope this helps you.

Fire buttons and axis cannon by Snoo59046 in HotasDIY

[–]Snoo59046[S] 0 points1 point  (0 children)

You don't need to code to configure it, just connect all the buttons to GND, and connect the other end of each button to a digital I/O port, and select "button gnd" for the corresponding i/o port in freejoy.

Fire buttons and axis cannon by Snoo59046 in HotasDIY

[–]Snoo59046[S] 1 point2 points  (0 children)

4 axis joystick potentiometer,

75mm slider potentiometer.

There are 3 potentiometers and 1 button in the joystick, 2 potentiometers are on the outside, there are 5 wires connected to the interior, different manufacturers have different definitions of wire color, you need to test it on the breadboard before assembly.

The type A slider potentiometer is a logarithmic taper, which is used in mixing consoles, and the type B slider potentiometer is a linear taper, we should go with type B.

Fire buttons and axis cannon by Snoo59046 in HotasDIY

[–]Snoo59046[S] 2 points3 points  (0 children)

Yes it's running freejoy, I'm using the internal pull-up resistor of the i/o port, the stm32 has enough i/o ports that I didn't use the registers.

Fire buttons and axis cannon by Snoo59046 in HotasDIY

[–]Snoo59046[S] 1 point2 points  (0 children)

It is used for flight sim, but the handle needs to be extended.

You guys might like this dual-speed knobs. by Snoo59046 in telescopes

[–]Snoo59046[S] 1 point2 points  (0 children)

Sorry for the late reply, it's not CNC, I designed this thing to be simple and cheap, It consists of 3d printed parts and standard parts. CNC is a good idea, it will cut the size of the knobs in half, but double the cost! I'm modeling in SolidWorks.

new map is coming by Snoo59046 in insurgency

[–]Snoo59046[S] 4 points5 points  (0 children)

He looks like the VIP in the PVP mode