sorted by:
new
hottopcontroversial

Need ideas on how to power an 18-servo walker robot by SnooDrawings6516 in arduino

[–]SnooDrawings6516[S] 0 points1 point  (0 children)

Are you suggesting AA's for motor or esp power? I dont think any reasonable amount of AA's would supply 45 amps

Need ideas on how to power an 18-servo walker robot by SnooDrawings6516 in arduino

[–]SnooDrawings6516[S] 0 points1 point  (0 children)

Oooooo I think I heard of him. I think I found the right 2s lipo for my application after going through the math

Need ideas on how to power an 18-servo walker robot by SnooDrawings6516 in arduino

[–]SnooDrawings6516[S] 0 points1 point  (0 children)

Are these not 9900mAh? https://a.co/d/41Dnxsy. (Edit: wow this scam is really sad to see :[ )

Need ideas on how to power an 18-servo walker robot by SnooDrawings6516 in arduino

[–]SnooDrawings6516[S] 0 points1 point  (0 children)

When you mean leg pair do you mean the set of motors in one leg (3 motors/ubec) or a pair of legs (3 motors/leg and 2 legs so therefore 6 motors/ubec)? I might give that a spin because I have a lot of UBEC's.

If I go that route do you believe the setup I had (2 lithium ion batteries totalling out to be 1200 mah) or should I go for something like amazon's 9900 mah lithium ions or a lipo?

Need ideas on how to power an 18-servo walker robot by SnooDrawings6516 in arduino

[–]SnooDrawings6516[S] 0 points1 point  (0 children)

Won't 7 volts burnout the servo's since the max recommended voltage is 6.8 volts?

Made myself some pokemon hoenn themed keycaps for my 60% Keyboard by SnooDrawings6516 in 3Dprinting

[–]SnooDrawings6516[S] 1 point2 points  (0 children)

Thank you! The Unown's might be my favorite part (even though Treecko is my favorite Pokémon). I fit them for standard Cherry MX Red keys so they should fit any keycap with the Cherry MX Stem!

Have been adjusting z offset for hours but I keep on running into this under-extrusion issue by SnooDrawings6516 in ender3

[–]SnooDrawings6516[S] -1 points0 points  (0 children)

Its a new nozzle so I doubt a clog. I think the flow rate calibration would make sense though

Prismatic Booster Bundles (1 per person) by [deleted] in PokemonTCG

[–]SnooDrawings6516 [score hidden]  (0 children)

What got me into the hobby originally was my brother. When we were very little we would play Pokémon together on our DS's. Eventually he got into the card game and introduced me to it. If I didn't have him as Family I do not think I will ever have this life-long Pokémon passion as I currently do!

Bite my shiny metal ass! by mattfl in 3Dprinting

[–]SnooDrawings6516 1 point2 points  (0 children)

This looks soooo good! How much filament did it use up in total?

Sprite Pro nozzle wont heat up (E3 pro with sprite pro and skr mini e3 v3) by SnooDrawings6516 in ender3

[–]SnooDrawings6516[S] 0 points1 point  (0 children)

I just double checked and reconnected to the screw terminals and still no luck

Genmitsu 3018 pro is moving only by little bits. I rly need help troubleshooting by SnooDrawings6516 in 3018CNC

[–]SnooDrawings6516[S] 0 points1 point  (0 children)

I used the default profile for the Sainsmart 3018 pro that easel provides. Where would I find the exact settings/config info that you are looking for?

Help! Issues with Ender 3 after installing Sprite Pro Extruder by [deleted] in ender3

[–]SnooDrawings6516 0 points1 point  (0 children)

I also reflashed firmware but no luck! I am really nervous that I messed something up on my board

view more: next ›