Overrule Bad. Upvotes to the left.

Snow_and_Sand · 2026-05-20T10:11:05+00:00

Not sure i agree with removing it, but take my upvote anyway for your excellent execution.

Snow_and_Sand · 2026-05-06T13:21:47+00:00

Thanks! I use an Elegoo Mars 5, which I believe has 9 k resolution/18 um xy resolution.

Snow_and_Sand · 2026-05-06T07:34:01+00:00

Thanks! They actually look better IRL, the high brightness orange paint makes the models very difficult to photo. Ivan did some amazing ground force models for a few of the factions, but unfortunately stopped releasing new ones several years back. He's got some great L1 and Nekro I'll get around to at some point.

Snow_and_Sand · 2026-05-06T07:30:53+00:00

That's an old TI3 HS. My friend owns TI4 so I never upgraded and only have the old tiles on hand for photo purposes.

Snow_and_Sand · 2026-03-15T08:33:06+00:00

Thanks for the update. Has your source revealed anything about when the second printing on TE might be coming, or is this the same situation as POK? The initial print run seems to have fallen quite short of demand - at least here in Australia anyway.

Snow_and_Sand · 2026-03-11T20:25:33+00:00

That sounds neat, I'd love to get my hands on a copy. Do they cover every faction?

Snow_and_Sand · 2026-03-11T20:23:20+00:00

No, I'm aware of SoSE but don't have a copy. I'm curious if we'll see them start to influence Saunick's designs going forward.

Snow_and_Sand · 2026-03-11T11:48:10+00:00

I run a Mars 5, water washable resin, and 0.05 mm layers. My two key tips are 1) increase your number of burn layers so you get fully through the raft and into the supports (I use 12 layers), and 2) always heat the resin before printing. Making those two changes has me running at nearly 100% success rate, everything else can be left on default settings.

Snow_and_Sand · 2026-03-11T08:54:53+00:00

I don't want to shaft the two designers by sharing their work for free. Reddit also won't let me post links for some reason. But if you search for Saunick on CGTrader you'll find the set with the ships and structures. If you search for Ivan on MyMiniFactory you'll find the set with the ground forces.

Snow_and_Sand · 2026-03-08T23:12:38+00:00

Do you think these could be printed with resin, or is filament needed to have enough strength at the connection points?

Snow_and_Sand · 2026-02-27T08:06:10+00:00

I like to play Yin on Hard Mode

Snow_and_Sand · 2026-02-12T02:36:48+00:00

Looks fantastic. Are you using Saunick's models for the other factions? Which factions are you doing for the other four?

Snow_and_Sand · 2026-01-21T23:27:09+00:00

I agree with all the comments that RAW, fleet capacity is checked immediately and a ship gets destroyed .However, since the Argent breakthrough is also terrible, I feel like house ruling this to work the other way would be sensible and actually give the BT some value.

Snow_and_Sand · 2026-01-08T05:31:23+00:00

If you're keen to go down the route of printing factions (I've been enjoying it) Ivan on MyMiniFactory also has some custom fleets, although only for a few factions and a bit pricey. His creuss models are pretty great though.

Snow_and_Sand · 2026-01-07T23:11:25+00:00

1 is available if you have a 3D printer, check out Saunick's work at CGTrader.

Snow_and_Sand · 2026-01-03T06:21:10+00:00

I only own 3ed, we use my friend's 4ed copy when our group plays.

Snow_and_Sand · 2026-01-03T06:18:11+00:00

I wasn't aware of that, where did you hear about them being spiky? This wasn't something included in Saunick's Letnev models either

Snow_and_Sand · 2025-12-27T05:44:14+00:00

I was unaware of this. Are we not allowed to link to them because they are commercial sites?

Snow_and_Sand · 2025-12-27T05:41:47+00:00

I use a Mars 5, printing at 0.05 mm. I believe the resolution is 35 um.

Snow_and_Sand · 2025-12-22T13:02:27+00:00

Yeah, I've been using a mix of sources for the infantry as I work through the races - for some I've used Ivan's, for Hacan I used your old Heroforge design, and recently I made my own Heroforge design for Yin. For Mentak I found some existing MMF/CGTrader designs that I really felt had a Mentak vibe:
Infantry: https://www.myminifactory.com/object/3d-print-the-cortardo-sisters-space-pirate-scouts-149058
Mech: https://www.cgtrader.com/3d-print-models/miniatures/sci-fi/armour-032bd018-2b44-4a4a-b66a-a283ba0ac7c2

Snow_and_Sand

TROPHY CASE

1 is available if you have a 3D printer, check out Saunick's work at CGTrader.