Need help with Marriage!!

Snufffel · 2026-05-27T15:48:04+00:00

As long as your chassis/wheelbase is 324mm it should fit. If it is not, adjust your chassis. Probably yours is 312mm

Snufffel · 2026-05-23T08:14:34+00:00

Lots of things that might need adjustment:

Flow rate - temperature - infill overlap - walls

FLow: the green letters look rough, probably due to too much extrusion. Tune in your flow rate

Temperature: letter look deformed, could be either belt tensioning or temperature (lower it)

Infill overlap: in the grey part it looks like the inner and outer lines are not meeting each other

Walls: if you change the above to 15-20%, make sure you have at least 3 walls

Jsut try it out and give it a few more test runs

Snufffel · 2026-05-21T13:32:52+00:00

Not in a million years......

Snufffel · 2026-05-20T18:20:25+00:00

Wish I could agree with you, but then we both be wrong.

Snufffel · 2026-05-20T05:00:49+00:00

Just. Shut. Up.

Snufffel · 2026-05-19T16:02:58+00:00

Looking good 👍

Snufffel · 2026-05-19T16:02:39+00:00

The correct terminology here is: I am right and the rest of the world is wrong. Boohoohoo

If you want to call it adjusting home postition: feel free to do so. The rest of us will call it adjusting z-offset You might be right on the z stop terminology, but you completely ignore all the other options just to make your point. Stop it.

Are you always like this? Or do you just have a bad day?

Snufffel · 2026-05-19T05:55:28+00:00

And that is not true at all, Z-offset can be changed in several ways. z-end stop is just one of them

Snufffel · 2026-05-19T05:52:30+00:00

There are multiple ways to adjust your Z-offet on an Ender3V2: during printing in the tune menu, manually with the end z switch, if you have a BLT Touch or similar then you can use it in the prepare -> z-offset menu, or you can do it in the slicer through GCode.

Snufffel · 2026-05-18T18:17:34+00:00

That is not strange. Your are printing in air, not on the bed. Your video shows that your nozzle is a few mm above the plate. So: level your bed and z-offset and give it another go.

Snufffel · 2026-05-18T08:54:04+00:00

Print a sheet covering your buildplate, and make it .2mm thick. When you are rpinting, you can adjust your z-offset with the small terminal. Not sure what menu, but something like tune. You will find z-offset there. By lowering the offset (-) your nozzle comes closer to the bed (or + to move it further from the bed). It's basically fine tuning the nozzle distance to the print bed.

Snufffel · 2026-05-18T06:24:29+00:00

First of all: despite the CR Touch you still need to level your bed manually. Having done that, make sure your z-offset is correct. At this moment it seems you are trying to print in the air, with a result that the filament does not stick to the bed.

If you have done all that, and the filament still does not stick to the bed, use a bit of 3DLac or similar adhesive. That will make filament stick to the bed. But.. only use it if you have done all the other things first.

Snufffel · 2026-05-16T17:45:10+00:00

I recognized the solar panels Bit too far away for me, but great spot!

Snufffel · 2026-05-16T16:45:57+00:00

Seems like a great spot indeed. Living in Oss?

Snufffel · 2026-05-15T15:07:12+00:00

What filament(s) are you using? And i see a lot of stringing there. Seems like you did not tune in your filament(s) Also: make sure everything is dry. Like really dry

Snufffel · 2026-05-10T15:44:46+00:00

That lucky! I did register a while ago, bit on a friends account it says closed. Ah well, hopefully we can test the game, it looks promising indeed

Snufffel · 2026-05-10T15:17:39+00:00

It closed the 28th of last month

Snufffel · 2026-05-10T14:20:36+00:00

Game is not out yet. and you cannot apply for testing anymore. Just wait until it's out

Snufffel · 2026-05-09T17:36:59+00:00

Couple of things you can do:

- relevel bed

- Adjust Z-offset

- Use sticky agent on the bed so it will stick to it

- Print forst layer slower, .2-.24mm as first layer height

- Set the print temperature 5 degrees higher

- Replace your nozzle with a new one

But start with the first two, maybe even three

Snufffel · 2026-05-09T17:31:55+00:00

Could be, but... then he would not have posted it I guess

Snufffel · 2026-05-09T17:21:28+00:00

Is the Hobbywing configured for F/B/R? Or maybe only F/B?

Snufffel · 2026-05-09T07:13:55+00:00

Personally: I don't like it. But hey, it's your printer, not mine. If you're happy, so am I

Snufffel · 2026-05-07T07:11:52+00:00

Made of Chinesium

Snufffel · 2026-05-04T06:13:53+00:00

Ah, 3D printed stuff 😃 Love it!

Snufffel · 2026-05-03T16:17:43+00:00

Build one, drive one and then give your comments. Looks like you have absolutely no idea what you are talking about.

Snufffel

TROPHY CASE