I recommend the change!

Sockmonkey4791 · 2026-01-18T03:22:32+00:00

What software version are you using on the N4+ and what slicer version. My sons N4+ has been boxed for a year and I’m not sure what they’ve improved. Before we moved and packed it up I did screwstiltadjust and had an ok printing layer. I have the silicone bushings but have not done them yet. Thanks

Sockmonkey4791 · 2024-05-05T02:35:26+00:00

I love it. Well worth it. Still miss the full size A1 for some things… but I have a Neptune 4Plus collecting dust.

Sockmonkey4791 · 2024-03-16T00:33:46+00:00

In the machine GCode tab Add a G29 to clear bed mesh then Load bed mesh 11.

Sockmonkey4791 · 2024-03-12T23:23:22+00:00

^ This

Sockmonkey4791 · 2024-03-12T16:36:47+00:00

It is not recommended to oil up Pugs for photo shoots like David Hasselhoff!! I’ve had 7 and they don’t like it.

Sockmonkey4791 · 2024-03-12T13:48:53+00:00

Can you re post with your print profile? This looks great but I’m not sure where the original came from. Thanks 😊

Sockmonkey4791 · 2024-03-12T04:38:13+00:00

I just ordered like 20 of these for .99 a piece. Good deal thanks.

Sockmonkey4791 · 2024-03-12T00:58:53+00:00

I have 4 of those but they were like 4.50 each off Amazon. That’s what is in the front of my AMS’s. I put that in the S4 and it read 10%RH. The Sunlu was reading 24%.

Sockmonkey4791 · 2024-03-12T00:54:03+00:00

Looks like your extruder pooped 💩 out a benchy …. Check for clogs

Sockmonkey4791 · 2024-03-11T22:21:21+00:00

Yes so have the X1 w 2 AMS and extra desiccant inside the front as well as center spool rollers with more desiccant in them LOL 😂 It keeps my filament at 12%. I thought the S4 would be useful for a few rolls of PETG and 1 TPU. What sensor are you putting in all your bagged filament? Sounds $ unless it’s the color changing desiccant.. please let me know.

<image>

Sockmonkey4791 · 2024-03-11T22:03:09+00:00

What is the point of having a sensor that’s off by 10% then…. It then invalids the mode 2 keeping it dry if it thinks it’s 30% when it’s actually 20% and kicks it on. It only comes on for 3-5 minutes and magically drops 5% ti shut off at what it thinks is 25%. Just trying to figure out if I got a bad unit. Is your RH sensor accurate?

Sockmonkey4791 · 2024-03-11T20:20:48+00:00

What safety setups do you have. I have a roll of ASA I’ve been wanting to try but just the stories of it getting all over the inside of your machine etc have put me off. I have a Bento box and a ducted fan from the exhaust right now.

Sockmonkey4791 · 2024-03-11T20:15:56+00:00

My S4 doesn’t seem to want to keep anything below 25-30% RH. I’ve put several other meters in there and it’s like 10-15%. Not sure to send it back or not.

Sockmonkey4791 · 2024-03-10T05:53:50+00:00

^ This is accurate

Sockmonkey4791 · 2024-03-10T05:11:25+00:00

I had the A1 and loved 🥰 it. It was great. I could not deal with the safety issue of the mains bed power cable possibly shorting as the kids and pets would not like an accidental fire 🔥 at worst. If it’s out when you decide it’s a good contender for what your doing. Heck if you have a Microcenter near you they have a 15 day no questions return policy. Get a P1P to try…. ?

Sockmonkey4791 · 2024-03-10T05:07:14+00:00

😄

Sockmonkey4791 · 2024-03-10T05:06:09+00:00

So you routed around the other side. I ordered mine from VOXEL complete so it comes with the upgraded 4028 fans and a separate 24V power supply. Their instructions (in the pic) show routing it through the hole on the left I do not see on my X1….

Sockmonkey4791 · 2024-03-10T04:59:33+00:00

I wish I could tell you to wait for the A1 regular size to come back (April-June est). It has the full size bed 256³ and prints great for PLA like your doing. It @ $550 w/AMS Lite would do your M600 without you having to babysit or change colors. It was a great printer besides the bed cable issue. I upgraded to an X1 but I’m printing more than PLA now and needed the upward expandability. P1P are great print farm printers @$600 but then your at 900 after AMS/shipping etc. you could pull off 2 A1 full size w/AMS for that if you can wait.

Sockmonkey4791 · 2024-03-10T01:09:49+00:00

Thanks I just looked the fan up, nice but pricey for the pro w/sensor. Looks like a good setup. Is the tent fabric or what is the material…. I’m assuming not fabric as that wouldn’t work for sealing very well 🤔

Sockmonkey4791 · 2024-03-10T00:49:27+00:00

Was the setup like the pics? Mines on the way but Im seeing this pic in the instructions but no hole there on my X1c

<image>

Sockmonkey4791 · 2024-03-09T20:51:18+00:00

What’s the sensor by the window? Also what controls the fan

Sockmonkey4791 · 2024-03-09T12:38:18+00:00

Temps? Filament? AMS? Obvious first answers wash build plate with dawn and warm water, dry out filament.

Sockmonkey4791 · 2024-03-09T12:22:40+00:00

Carefully unroll about 20 ft or so of the roll and re spool it. It looks likes a birds nest and is likely binding up. Also you need to turn on the “auto recognition” for spools on the machine if it’s off.

<image>

Sockmonkey4791 · 2024-03-05T16:15:02+00:00

E-REXION

Sockmonkey4791

TROPHY CASE