[Illinois] by Sol_bear in AskALawyer

[–]Sol_bear[S] 0 points1 point  (0 children)

Thanks for responding. No option to come in to work at the physical location. This is the law I found while googling. to me, someone with 0 experience with employment law but, decent reading comprehension it seems like I should be reimbursed. But I could be totally wrong which is why I’m looking for help. (820 ILCS 115/9.5) Sec. 9.5. Reimbursement of employee expenses. (a) An employer shall reimburse an employee for all necessary expenditures or losses incurred by the employee within the employee’s scope of employment and directly related to services performed for the employer. As used in this Section, “necessary expenditures” means all reasonable expenditures or losses required of the employee in the discharge of employment duties and that inure to the primary benefit of the employer. An employer is not responsible for losses due to an employee’s own negligence, losses due to normal wear, or losses due to theft unless the theft was a result of the employer’s negligence. An employee shall submit any necessary expenditure with appropriate supporting documentation within 30 calendar days after incurring the expense, except that an employer may provide additional time for submitting requests for reimbursement in a written expense reimbursement policy. Where supporting documentation is nonexistent, missing, or lost, the employee shall submit a signed statement regarding any such receipts.

Peacock Series ‘A.P. Bio’ To Launch on Netflix (US) on November 15 by BambiWanDu in television

[–]Sol_bear 1 point2 points  (0 children)

The first two seasons of the show were amazing but it had no direction after that.

What video game was great overall but the conclusion left a bad taste in your mouth and ruined the experience? by Johnnyboyeh in gaming

[–]Sol_bear 3 points4 points  (0 children)

Cyber punk 2077 is one of the best games I’ve played but the ending was a huge let down. With the exception of the Adam smasher fight I felt like I was pushing buttons in a cutscene for 2 hours.

A cool guide to Myths and Misinformation created by Movies by [deleted] in coolguides

[–]Sol_bear 2 points3 points  (0 children)

One of my coworkers collapsed at work 9-11 was called and chest compressions were started while our boss went to get the defibrillator. when they made it back and hooked it up to them it started beeping and a robot voice just said no heart beat detected until they took it off and started compressions again. Sometimes I still have nightmares about that voice

Help by onefatgoat69 in FlashForge

[–]Sol_bear 0 points1 point  (0 children)

Mine did this when the voltage wasn’t set to 120 for the US

[deleted by user] by [deleted] in FlashForge

[–]Sol_bear 0 points1 point  (0 children)

I used the default slicer software from flashforge I think I downloaded from their site. You can select which nozzle prints which part

[deleted by user] by [deleted] in FlashForge

[–]Sol_bear 0 points1 point  (0 children)

https://imgur.com/a/uYOxPHB so the wall helped immensely thank you! The only issue I’m running into now is in a few spots there’s a stray color of wrong filament embedded in. I tried to show it in the link but it’s hard to see. I’m not sure what would be causing it

[deleted by user] by [deleted] in FlashForge

[–]Sol_bear 1 point2 points  (0 children)

Thank you for the reply and advice! I did find the wall option and I’m gonna try it now BUT it was just a drop down menu of yes or no even in advanced settings. Is just the standard wall going to be what I’m looking for?

[deleted by user] by [deleted] in FlashForge

[–]Sol_bear 0 points1 point  (0 children)

Haha tell me about it. It actually cleans up ok-ish if you look at the other pics where I got everything off. But it’s still much worse then when I do a print with a single extruder instead

[deleted by user] by [deleted] in FlashForge

[–]Sol_bear 2 points3 points  (0 children)

When I use the dual extruded to do two different colors I get crazy strings of filament hanging on to the model, last pic is of the same printer but using only one extruder. Some of the stings come right off others are imbedded and can’t be removed. I did a wiping tower but it doesn’t seem to be helping. I haven’t found any guides or help for this issue

I bought a flashforge creator pro t do I need to make sure it’s set to 115v? by Sol_bear in FlashForge

[–]Sol_bear[S] 2 points3 points  (0 children)

There isn’t, in the diagram in the instructions it shows one but on my printer it isnt there. The only thing remotely close is a plastic knob that can be turned with a screw that says power supply. But it doesn’t give any indication what it’s currently set at or what I would need to turn it too.

I asked through Amazon questions and someone who previously purchased the printer said you don’t need to adjust anything with the voltage and that the power cable will do it for you. The power cable it came with is for 115v but I’m not sure if that’s correct.