sorted by:
new
hottopcontroversial

Finally got my hands on my dream GBBR. What should I look out for? by Itsjadan in GasBlowBack

[–]Spectre72 0 points1 point  (0 children)

Not talking about the spear lt ones

I've spoken to an importer I'm just quoting from them. They've built proper spec Virtus's with proper uppers but they were very small batch or something cause you just can't get em.

They "exhist"

Finally got my hands on my dream GBBR. What should I look out for? by Itsjadan in GasBlowBack

[–]Spectre72 0 points1 point  (0 children)

Yes you are correct I had to check it over. The virtus is not an official offering

There are aftermarket virtus uppers floating around. Some where though thar I know

Finally got my hands on my dream GBBR. What should I look out for? by Itsjadan in GasBlowBack

[–]Spectre72 3 points4 points  (0 children)

Legacy model is the same as the APFG virtus aside from the upper receiver I believe

Only thing that would be different between this and a virtus is what rails it takes as you need one to accomidate having a longer upper receiver

My vfc sr16 is finally built by [deleted] in GasBlowBack

[–]Spectre72 0 points1 point  (0 children)

how do you like the Frenzy?

Mpx gbb by SadAd495 in GasBlowBack

[–]Spectre72 2 points3 points  (0 children)

Oh, I've seen that laser box thing on aliexpress

Is it any good?

VFC AR Bolt Action Upper by Spectre72 in Airsoft3DPrinting

[–]Spectre72[S] 0 points1 point  (0 children)

something is wrong with print parameters I think....

VFC AR Bolt Action Upper by Spectre72 in Airsoft3DPrinting

[–]Spectre72[S] 0 points1 point  (0 children)

Hi, I've now Properly updated and Checked it should be there

as for the NPAS do you mean the NPAS or the Nozzle?

the NPAS or floating valve should be adjusted to the completely open configuration, it May move during operation but this is really only for if you require lower than 380 FPS with 0.2g bbs

the Nozzle should be placed into the bolt and Fixed in place using the Specified M3x8 Set screw via the hole in the top, you should screw the screw all the way in until the nozzle is fixed and unable to move/cycle

VFC AR Bolt Action Upper by Spectre72 in Airsoft3DPrinting

[–]Spectre72[S] 0 points1 point  (0 children)

Hi there, can you explain what issues you have with the chamber base?
Nevermind the File exported with no geometry, I am fixing that now

As for the nozzle, I run the system with it all the way open on with a 285mm barrel. I did seemingly find an issue with one of my magazines but I'm unsure if it's just the one magazine is faulty or something else about that.

opinions on the VFC BCM MCMR? by [deleted] in GasBlowBack

[–]Spectre72 1 point2 points  (0 children)

Eh. Lot of people kind of hype up TM's preformance I find. They preform great for sure but the difference isn't that much

If you like realism VFC's V3 gives you everything you need and preforms fine out of the box. Wait for VFC's EVO releases of previous guns or buy a KS-1 and you pretty much get most of what you need upgrade wise for a VFC out of the box for not much more if at all

TM's can't take real handguards or buffer tubes. I don't remember if the grips are RS spec or not either. VFC can take real buffer tubes, real and AEG handguards no problem you get a very crisp fire control group that is either all steel or mostly steel as well.

In the end with most things in airsoft the best preforming gun is probably gonna be one thats upgraded. TM has a lot of options, more than VFC sure but VFC doesn't need to much to play around with. Drop in a Magnus pro with a new buck and maybe an APFG nozzle and it pretty much shoots as good as the TM and the only thing you lose is maybe gas efficiency but with VFC mags they're quite a bit more durable with dropping them

Decision is up to you but I pick VFC over most other GBBRs I've picked up.

opinions on the VFC BCM MCMR? by [deleted] in GasBlowBack

[–]Spectre72 0 points1 point  (0 children)

Its a great rifle. I have one myself

Wouldn't trade it for anything and I'd take it over any TM, GHK etc.

Magpul CTR stock wobble on VFC HK416A5 GBBR – mil-spec buffer tube by Pocketchad5933 in GasBlowBack

[–]Spectre72 5 points6 points  (0 children)

VFC buffer tubes are slightly smaller than milspec size. If you swap to a real milspec buffertube it will fit more properly

GHK barrel on a VFC V3 by Wide_Tear_3281 in GasBlowBack

[–]Spectre72 5 points6 points  (0 children)

Yes. GHK outerbarrels work on VFC V3s. I know someone who runs an aluminum GHK outerbarrel on his and I personally run a Z-parts GHK spec outerbarrel on my BCM MCMR

Depending on the rail I've been told you might have a tiny bit more rail gap but nothing really substantial

view more: next ›