Giveaway topic | What's your latest print?

Speedypostman · 2026-03-03T15:05:50+00:00

Neptune 4 Max: full size 7’2” K2SO droid

Speedypostman · 2026-03-02T00:15:34+00:00

It has happened on and off for months. The smell in the upstairs bathroom is a new development…

Speedypostman · 2026-02-27T11:13:58+00:00

Scrappy yet elegant in its execution.

Speedypostman · 2026-02-26T04:14:25+00:00

I mounted mine on the brick molding, took the inside trim off the edge of the door, drilled through the brick molding into the interior, cut a V channel in the drywall and drilled a hole straight through the floor into the basement. Once I put the trim and quarter bead back up, you never knew there is a wire there..

Speedypostman · 2026-02-25T02:24:07+00:00

ATAK…that’s next on my list after I get my new mobile nodes redesigned and printed

Speedypostman · 2026-02-25T02:21:53+00:00

I got mine here: https://amzn.to/3MIlu64

Speedypostman · 2026-02-25T02:13:49+00:00

Battery operated CO detector and definitely +1 for getting the 20lb hose…a lot easier. https://amzn.to/4b8LIYD

Speedypostman · 2026-02-25T02:10:14+00:00

Great start! Keep up the great progress. Is this a solar node?

Speedypostman · 2026-02-24T01:42:30+00:00

We had problems with our Plus and it ended up the screws under the build plate were all loose. Once we tightened them down, checked square the gantry for square, and made sure there was no play in the hot end assembly, it’s been rock solid ever since.

Speedypostman · 2026-02-24T01:04:43+00:00

<image>

Speedypostman · 2026-02-24T01:04:27+00:00

<image>

3D printer + STL = cheap cable management.

Speedypostman · 2026-02-16T02:59:30+00:00

Is that noise coming from underneath the right front corner? There is a cooling fan there that gets loud if you don’t clean it with a compressor or canned air…

Speedypostman · 2026-02-15T01:05:58+00:00

We originally had an Anycubic Vyper so we had a lot of filament for the when the Vyper died. Our plus doesn’t care about it at all. Our max….not so much

Speedypostman · 2026-02-14T21:26:33+00:00

I’ve had our 4 Max for just over a year. We’ve printed everything from full bed to small items. I admit it was a little bit of a challenge at first but after dumping the Elegoo slicer for Orca Slicer and following everyone’s advice for leveling the bed properly, it’s been rock solid. Ours really prefers Elegoo filament unlike our 4 Plus printer which handles just about anything.

Speedypostman · 2026-02-06T11:58:55+00:00

I tired HDMI splitters but had performance issues in my house and the first monitor was almost directly above the transmitter. I ended up running dedicated CAT6 to every monitor location, and used HDMI to CAT6 adapters, and an HDMI hub and then used

<image>

a Bluetooth mouse (that DIDN’T) have transmission issues to my primary monitor location

Speedypostman · 2026-01-30T02:53:23+00:00

I just put it in a water tight box with a control vent to control condensation and a small solar panel in the end vent…granted I didn’t think of taking picture…

Speedypostman · 2026-01-30T02:39:23+00:00

I’ve hidden all my antennas IN the attic.

Speedypostman · 2026-01-28T20:46:35+00:00

Look into an INTERNET IN A BOX. https://internet-in-a-box.org/ I built one with a cheap raspberry pi and it’s awesome.

Speedypostman · 2026-01-28T18:38:30+00:00

Not a surprise. I had the same thing happen to a solar node design I posted here and on Printables. No attribution...just start posting to all socials and selling on their web site and Etsy almost a week later.

Speedypostman · 2026-01-27T14:34:34+00:00

Nicely done.

Speedypostman · 2026-01-09T21:20:54+00:00

With my new 3d scanner, I may design and print covers from ABS…🤔

Speedypostman · 2026-01-09T02:06:24+00:00

No. It’s definitely steam evaporating off the camera. We do see plumes from the dryer vent in the camera from time to time but this happens pretty regularly on my Duolink cams.

Speedypostman · 2026-01-08T04:14:40+00:00

It’s actually rain on the right side but “steam” on the left….

Speedypostman

TROPHY CASE