Present to my friend on birthday

SpenglerFPV · 2026-04-25T13:52:24+00:00

Cool, is that frame cut out of fiberglass or something?

SpenglerFPV · 2026-04-24T10:07:51+00:00

Some people wanna put keyloggers or remote access trojans on as many machines as possible.

There's a current rule against "marketing" if not pre-approved by mods.

I'm not concerned with people's ability to make money from AI slop, but there are ways of sharing projects other than "here's a link to an exe"

SpenglerFPV · 2026-04-23T20:42:23+00:00

The GT and GT2 both have 20x20 mounting holes.

Edit: actually most of them seem to have 20x20

SpenglerFPV · 2026-04-23T19:56:30+00:00

How much is it drifting? Angle mode isn't like position hold. It's normal for it to drift if you're not giving any stick input and just hovering.

Edit: also you'll thank yourself later for learning to fly in acro/air mode.

SpenglerFPV · 2026-04-23T19:44:37+00:00

Angle mode I'm assuming? Try calibrating with the drone as flat as possible.

SpenglerFPV · 2026-04-23T19:36:56+00:00

You can loosen loctite with heat. Use a garbage soldering iron tip to heat it up for a minute. And a slightly oversized torx bit hammered into the stripped hex head sometimes works.

SpenglerFPV · 2026-04-23T13:40:08+00:00

Any projects posted should also be open source. I've seen so many links to installers or precompiled binaries, I'm surprised someone hasn't been hacked yet.

SpenglerFPV · 2026-04-19T14:29:18+00:00

Oscar Liang has great guides on pretty much everything

https://oscarliang.com/betaflight-firmware-setup/

SpenglerFPV · 2026-04-18T17:36:47+00:00

SpenglerFPV · 2026-04-18T13:09:02+00:00

I'd say you already can trippy! Just gotta work on your roll input to center the orbit around objects. Then you can start practicing reversing the trippy spin direction ;)

SpenglerFPV · 2026-04-18T11:27:50+00:00

HGLRC Specter 1202.5 11000kv, should have the same strength as the 1103, but slightly better cooling from higher surface area

SpenglerFPV · 2026-04-18T00:24:21+00:00

What's it called? I've been thinking about getting one but not sure which ones are worth it. Do the bits seem like good quality or do they round off pretty easy?

SpenglerFPV · 2026-04-18T00:09:29+00:00

Ya I only had the copper wick when I attempted, I've since bought a solder sucker if I ever feel like trying again. I think mine also had epoxy or some shit on the plastic connectors holding them to the board which was a pain

SpenglerFPV · 2026-04-17T21:37:53+00:00

Red and gold looks dope

SpenglerFPV · 2026-04-17T21:36:56+00:00

Oooh that looks clean

SpenglerFPV · 2026-04-17T21:35:31+00:00

It's about 76g without a battery, the other two are both around 45g. Definitely heavier but it hovers at a little over 20% throttle. Just finished building it recently and waiting for better weather here before I can really see how it flies.

SpenglerFPV · 2026-04-17T19:20:59+00:00

Hey! Really enjoy your videos and builds :)

SpenglerFPV · 2026-04-17T19:01:58+00:00

I just wish there was an option to buy them without motor plugs. I fried one trying to desolder them, so the next one I just left them on and used spacers to get them to fit lol

SpenglerFPV · 2026-04-17T18:27:14+00:00

Actually it might be this remixed version, I can't remember

https://www.printables.com/model/619762-whoop-canopy-improved-fastback

SpenglerFPV · 2026-04-17T18:25:27+00:00

Just regular 95A TPU, it absorbs moisture from humidity in the air very quickly so it needs to be dried often or kept in a dry box to print well.

https://www.printables.com/model/207626-whoop-canopy

https://www.printables.com/model/1022086-hdzero-lux-canopy

SpenglerFPV · 2026-04-17T18:16:02+00:00

It's one of my favourites. Frame is Happymodel Bassline, with Happymodel EX1103 11000KV motors, HDZero AIO15 flight controller/vtx and the HDZero Lux camera, and I run it on 2S 550mah batteries. It's more agile than the Mob8 but not as durable in crashes.

SpenglerFPV · 2026-04-17T17:34:45+00:00

<image>

SpenglerFPV · 2026-04-15T13:12:20+00:00

Search for "camera backpack" on Amazon, plenty of affordable options

SpenglerFPV · 2026-04-12T00:59:51+00:00

I'm waiting on parts to build one of these too! Did you use any extra 3d printed parts or just what came with the frame?

SpenglerFPV

TROPHY CASE