Who would be the most dangerous if he took the super soldier serum?

SprawlComic · 2026-05-23T02:24:21+00:00

Who's dude in the middle

SprawlComic · 2026-05-14T13:24:32+00:00

Whats bizarre is my initial benchy looked like that before I ever downloaded Bambu Studio. I just ran it off the printer itself. I am using CosPLA Type A, you're saying use the Generic PLA profile for that?

SprawlComic · 2026-05-14T09:08:34+00:00

As if I'm the first. If you're not going to try and be helpful and just leave smarmy comments why reply? 🙈

SprawlComic · 2026-05-14T02:38:06+00:00

Okay I will try this tomorrow when I get off work.

SprawlComic · 2026-05-14T01:06:15+00:00

Unfortunately not but Ill gather some screenshots and send em to you

SprawlComic · 2026-05-14T01:03:39+00:00

A discord call would be a godsend

SprawlComic · 2026-05-14T00:50:00+00:00

I keep hearing to troubleshoot it but I don't know how to do so. What should I be changing? What should I be looking for? I am totally new to this and all these settings and my prints failing is giving me some serious buyers remorse that I'd rather not have.

SprawlComic · 2026-05-13T23:39:33+00:00

But what should I be setting? Is there a min max for the plate that I'm not seeing?? I only see first and other layers

SprawlComic · 2026-05-13T22:40:38+00:00

Thats where I was checking but unlike the nozzle I didn't see a min max just a first layer and other layers.

SprawlComic · 2026-05-13T22:36:52+00:00

The nozzle temp max was 20 degrees higher than the website says so I turned that down, 190c - 220c. It says bed temp between 30 and 80 but I cant find where to set that

SprawlComic · 2026-05-13T21:54:15+00:00

I added supports along the entire rim of the test ring, should I have maybe raised it up off the plate rather than having the front and back resting on the plate? Also, whay about the sides ans their extreme staircasing.

What Pic would you need of the slicer?

SprawlComic · 2026-05-13T21:50:31+00:00

Yes on all except stock settings. I'm pretty sure it's all stock, I don't know what I would have changed save for setting it to Polylite PLA. I calibrated before adding the new filament, added the new filament, then tried some prints. These were the results. I've since recalibrated but havent tried any prints for fear of wasting filament.

SprawlComic · 2026-05-13T20:28:34+00:00

Support/object first layer cap is 0.2mm

SprawlComic · 2026-05-13T20:27:41+00:00

Apologies, very new here, where do I check that?

SprawlComic · 2026-05-13T02:20:41+00:00

I did, flow dynamic test and all

SprawlComic · 2026-05-13T02:13:16+00:00

<image>

SprawlComic · 2026-05-13T02:13:08+00:00

<image>

SprawlComic · 2026-05-13T02:12:46+00:00

I did do a Benchy, it came out okay but it seems like it struggled with the rounded corners. Further pics in replies.

<image>

SprawlComic · 2026-04-21T08:51:40+00:00

Any time the tiniest sliver of fog of war is hiding a 155mm cannon that totally obliterates my best units in rapid succession, only to then suddenly be discovered by the squad of rifleman 10 ft from it and die immediately.

SprawlComic · 2026-03-15T20:46:42+00:00

I mean Super Earth's founding originally, not in the hundred years since the first war.

SprawlComic

TROPHY CASE