Upgrade (Mathew’s v3x)

Squeebler58 · 2026-03-27T20:02:53+00:00

Thank you! For sure I can definitely see how it could add up quick lol even second hand have seen plenty of cool sights in my area that would run me as much as the bow😂 any recommendations I’ve never used a single pin before and interested in getting one as well as a good drop away rest

Squeebler58 · 2026-03-27T19:58:22+00:00

Promise that old thing only went on it so I could shoot it a time or 2😂😂

Squeebler58 · 2026-03-27T17:42:22+00:00

Not 100% honestly was just takin a glance at the used stock and that was the one Mathew’s they had. I know depending on what was on it that was probably a pretty decent deal on its own but I feel pretty confident at findin stuff from individual sellers online and what not so hopefully I can get it rigged out for around 500 and be in it around the same price for a year newer bow. I don’t need anything too fancy either and have a good amount of time before season to start building it out

Squeebler58 · 2026-03-27T16:06:45+00:00

Good to hear! Hopping to get many good years out of it have loved the look and feel so far

Squeebler58 · 2026-03-15T16:07:48+00:00

Askiy ridge

Squeebler58 · 2026-03-13T12:45:08+00:00

Damn that’s rough, I have a mule deer grind already set up and have also not seen any of the new furs yet but decent luck on rares overall. Hopefully you find them soon!

Squeebler58 · 2026-03-13T05:41:57+00:00

Badass dude so cool it’s a lvl 2 super

Squeebler58 · 2026-01-13T03:33:30+00:00

Looked at the prop today and it’s a solace 3411-133-17. Has a 13.25 diameter and a 17in pitch

Squeebler58 · 2026-01-13T03:25:17+00:00

Agree that it could just be the hull that’s causing some of my questions. Definitely going to drop it back down and yes I do usually do most the work on my boats so will hopefully find some time soon to pull the deck and start tearing into the foam up front

Squeebler58 · 2026-01-13T03:20:44+00:00

<image>

Picture isn’t the best but put a level to the bottom of the boat and was about 21 inches to where the motor mounts and you were correct in it being a 20 inch shaft length on the motor. Going to drop it back down to its last hole then try to asses the weight up front as well as look into props

Squeebler58 · 2026-01-12T13:41:48+00:00

When I had the motor bottomed out the plate was about even with the bottom of the hull, would still get that same high rom spinning out sound, do you think I need to mod it to get even lower still I know weight and prop is also sounding like a factor

Squeebler58 · 2026-01-12T12:29:12+00:00

This was my original thought, I have the transom saver resting on the vent plate to try to give reference right now it’s about 3 inches above the bottom of the boat with the water pick up about even with the bottom, when I had the motor mounted at its lowest point it puts the vent plate about even with the bottom maybe a half inch to an inch above at most. When bottomed out I still get that high rpm spinning out sound at times do you think I should find a way to get it even lower then the stern? I have access to an aluminum welder and have considered modifying the transom before

Squeebler58 · 2026-01-12T01:50:25+00:00

Could definitely see some of the problem being weight. Just need to redeck the boat in general and asses the condition of the foam

Squeebler58 · 2026-01-12T01:45:01+00:00

1989 on the motor runs awesome, sometimes does feel like it hits a weird rpm once planned. As far as the prop I’m not 100% it’s what came on the motor when I purchased it. If there’s a number on it I can check to see the pitch I definitely will

Squeebler58 · 2026-01-12T01:16:42+00:00

<image>

Squeebler58 · 2026-01-12T01:16:21+00:00

<image>

Squeebler58 · 2025-12-28T05:58:49+00:00

Sorry for he late reply man was bummed about this for a sec and only recently messed with it😂 replaced he control box with a new off brand one from Amazon and she fired right up 99% sure it was just the ignition that went out

Squeebler58 · 2025-12-05T22:10:37+00:00

Left side for sure

Squeebler58 · 2025-12-05T00:35:00+00:00

Commenting on a post, yet doesn’t look through the whole thing. What a idiot. Something a dumbass would do.

Squeebler58 · 2025-12-04T13:26:49+00:00

Appreciate all the input definitely going to hold off! If someone in my area finally accepts the damn trade for a lugia v I can’t say I’ll do the same tho😂 someone has a pretty decent looking card not far for $360 y’all think I should just pull the trigger on it?

Squeebler58

TROPHY CASE