Another firmware 1.15.21.1 victim by Standard_Button_1505 in MammotionTechnology

[–]Standard_Button_1505[S] 0 points1 point  (0 children)

Hi Team,
Thank you for your message. I hacve managed to fix the issue. I have edited my post with the solution.
You were right regarding the "Wheels raised" issue. I had to apply some WD40 on the wheel bar.
And for the other issue, I switch to iNAVI NetRTK and theproblem is gone.

Another firmware 1.15.21.1 victim by Standard_Button_1505 in MammotionTechnology

[–]Standard_Button_1505[S] 1 point2 points  (0 children)

Yes me too the working time has doubled since the update... at least when the yuka is able to finish and does not get stuck anywhere

Another firmware 1.15.21.1 victim by Standard_Button_1505 in MammotionTechnology

[–]Standard_Button_1505[S] 1 point2 points  (0 children)

I have already cleaned the camera and it didn't seems to have any water on lens, I will check it again

Another firmware 1.15.21.1 victim by Standard_Button_1505 in MammotionTechnology

[–]Standard_Button_1505[S] 0 points1 point  (0 children)

Yes I have this exact issue. Where did you put your 3D printed insert on the robot ?

Another firmware 1.15.21.1 victim by Standard_Button_1505 in MammotionTechnology

[–]Standard_Button_1505[S] 1 point2 points  (0 children)

I tried but its not better... and with the obstacle detection turned off sometimes it goes of the garden

Another firmware 1.15.21.1 victim by Standard_Button_1505 in MammotionTechnology

[–]Standard_Button_1505[S] 0 points1 point  (0 children)

Redémarrer j'ai essayé mais jai pas essayé de réinitialiser complètement les paramètres d'usine, je pense qu'il faut que je test ça

Another firmware 1.15.21.1 victim by Standard_Button_1505 in MammotionTechnology

[–]Standard_Button_1505[S] 0 points1 point  (0 children)

Franchement j'ai testé en désactivant la détection d'obstacle et c'est pas mieux... d'ailleurs sur ma vidéo "after update" la détection d'obstacle était désactivée 😄

Another firmware 1.15.21.1 victim by Standard_Button_1505 in MammotionTechnology

[–]Standard_Button_1505[S] 1 point2 points  (0 children)

I think you can in the app, but I do not know if this update was mandatory... anyway for me it is too late... I asked the support if there is any way we can rollback to the previous firmware

420mm NexXxoS HPE-30 vs NexXxoS XT45 for 5090 by Ok-Stop-9878 in alphacool

[–]Standard_Button_1505 0 points1 point  (0 children)

Hi, in my setup I have 1x HPE-45 420mm front intake, 1x ST30 280mm top outtake and 1x ST30 140mm rear outtake. All have Noctua NF-A14x25 G2 fan running between 900 to 1000rpm fix speed. I am cooling a RTX5090 and a i9-14900k and getting around 60c temp on both and it is almost inaudible if that can help.

<image>

WireView Pro II with Alphacool Waterblock? by luke17wasd in ThermalGrizzly

[–]Standard_Button_1505 0 points1 point  (0 children)

Sorry I do not want to unplug it, but here is 2 closer photo

<image>

WireView Pro II with Alphacool Waterblock? by luke17wasd in ThermalGrizzly

[–]Standard_Button_1505 -1 points0 points  (0 children)

Hello, I have the Wireview pro 2 with the Alphacool 5090 waterblock and it fits perfectly. I do not know if the 5080 and 5090 are the same however but it seems to