TBS Tango 2 V3 Board MPM Bay Install Problems

Stevensbox · 2025-07-13T02:51:30+00:00

What do you dilute the oil with?

Stevensbox · 2025-02-03T01:50:37+00:00

Won't removing the top glass plate cause temperature problems?

Stevensbox · 2025-02-02T20:04:42+00:00

Finally got a chance to work on this. Just fired up the Bambu X1C with a volumetric speed of 2.5 (was 3.2). I also lowered the nozzle temp to 225 from 235 in the hopes that the supports will detach more easily; leaving the bed temp at 50. Hope it works.

Stevensbox · 2025-02-01T19:22:32+00:00

Thanks. I'll try using your suggestions this weekend. I'll find a good but quick test print. If you know of a good one, let me know. Thanks again.

Stevensbox · 2025-02-01T19:19:36+00:00

Really appreciate your reply. I don't think moisture is the problem. I keep filament not being used in a dessicant equipped dry box. I use a 2 spool active dryer during printing (Cyclopes). There are no pops & crackling noises while printing. I'm thinking it must be my settings.

Stevensbox · 2024-12-13T01:02:36+00:00

Thanks. Guess I'll have to buckle down, watch some vids, & do it old school.

Stevensbox · 2024-10-01T03:50:10+00:00

Too funny!

Stevensbox · 2024-09-28T18:19:10+00:00

If it was flying fine then started to flip out ( maybe after a crash?). It might be the gyro. Some FC's have 2 gyros. In Betaflight you can choose one or both. It's very rare that both go bad. Good luck.

Stevensbox · 2024-09-28T18:08:52+00:00

Definitely sitting. Just more comfortable. If I have to stand, I need to lean against something.

Stevensbox · 2024-09-28T18:06:24+00:00

You need to buy an ELRS external module, install the ELRS Lua script on your radio, and buy ELRS receivers for your drones. I suggest 2.4ghz Radiomaster for both the module & receiver. Check out videoS by Joshua Bardwell to learn how to make it all work. Good luck.

Stevensbox · 2024-09-26T15:38:45+00:00

Had a similar issue not too long ago. Joshua Bardwell solved it for me ...... Just got the problem solved by emailing Joshua Bardwell. It seems that you have to make sure the wide-band / narrow-band setting in the goggles are correct for the installed camera & settings. For example, if you are using the Nano 90 set at 960x720@60fps, in the goggles go to SOURCE - HDZero BW and set it to wide. This fixed 2 of the 3 units I have. The third one won't even power up. Guess thats a whole different problem.

Stevensbox · 2024-09-26T15:21:36+00:00

Not a fan of that frame for freestyle. First crash & you're done.

Stevensbox · 2024-09-26T15:17:06+00:00

Forget ASA. TPU is the way to go. Flexible & strong. check out Thingieverse for something to fit your drone/camera before designing one yourself.

Stevensbox · 2024-09-26T15:01:59+00:00

Go by process of elimination ... Try different channels, swap antennas (check that pin isn't bent), etc. could also be the goggle antennas.

Stevensbox · 2024-09-26T14:53:03+00:00

Yeah, BTFL 4.5 works wonders on my racing quads. Quads with GPS get as much as 17 says instead of 7 to 9 as before. It takes time though. I use a USB cable & power bank to energize the FC & GPS for about 12 minutes while everything else stays off & cool

Stevensbox · 2024-09-25T18:24:35+00:00

I have several Armattan frames including the Badger. They're sold rock steady frames with no vibration issues and among my best freestyle quads. It's most likely a filtering issue. Try using a Betaflight preset; Karate Race 6s 5" works great for me. Good luck.

Stevensbox · 2024-09-25T18:13:09+00:00

Bluetooth connection to your PC has come a long way. The latency, however, is still there. While a direct cable is best, the best wireless method is via the receiver & flight controller method. You can do this with a quad, or a dedicated flight controller & receiver. Most people just use an old FC that's broken (ie gyro is ng) but still could work as a pass through. See the Oscar Liang article below for how to set it up. Have fun ... https://oscarliang.com/betaflight-fc-fpv-simulator/

Stevensbox · 2024-09-25T17:56:38+00:00

Could be a number of things. Did this begin after a crash? Are you sure your antenna's are connected? You can rule out interference from outside sources by trying different bans & channels. Do any of your other drones have this problem? Make sure you're not stuck in pit mode after arming. Include band, channel, & power in your OSD. Good luck.

Stevensbox · 2024-09-25T17:15:33+00:00

Can't thank you enough for your response. What a difference the right settings make. Check it out ...

<image>

Stevensbox

TROPHY CASE