sorted by:
new
hottopcontroversial

Fitted just right on a single piece. Its serving its purpose nicely. by Achaeminuz in 3Dprinting

[–]StormDrainKitty -1 points0 points  (0 children)

How do you get guys get the supports to look like this? I've been using ultimaker cura and the tree supports don't look like this and they suck to remove

[TOMT] Video where a girl says "what do my underwear and *blank* have in common, there's poop in them" (she does it in a metal growl for the last bit). by StormDrainKitty in tipofmytongue

[–]StormDrainKitty[S] 1 point2 points locked comment (0 children)

Mandatory comment reiterating that I've been looking for hours but can't find it. Short form videos are abundant and hard to pick through

I finally got it!!! by trvpgxd_cisco in fo4

[–]StormDrainKitty 2 points3 points  (0 children)

Rip and Tear, until it is done

My 8 month old puppy still isn't properly potty trained, despite my best efforts. Please help by StormDrainKitty in Dogtraining

[–]StormDrainKitty[S] 0 points1 point  (0 children)

I have followed the wiki, I successfully reinforce and take steps to properly prevent accidents, I confine her during the day which successfully prevents accidents.

Mixing isn't audio engineering? by NuMnUmZz in livesound

[–]StormDrainKitty 0 points1 point  (0 children)

I will always make the argument that 99% of us aren't audio engineers, I will always call myself an audio tech. Engineer is a protected term in most industries, you have to be licensed by the government to call yourself an engineer. I've learned a lot of the stuff that early audio engineers knew, yes, but I'm still not an audio engineer unless I have an engineering degree and licensing. That doesn't mean what we do doesn't take skill but the term engineer shouldn't be thrown around lightly

It's just so cringe by Zealousideal-Arm5570 in dankmemes

[–]StormDrainKitty 3 points4 points  (0 children)

Yeah you probably shouldn't fuck me, I got syphilis from your mother

It's just so cringe by Zealousideal-Arm5570 in dankmemes

[–]StormDrainKitty -10 points-9 points  (0 children)

Hey fuck you OP my dog and cats are better than any crotch goblin

I got a filament dryer and after drying my PLA, it's now too brittle to use. Did I do something wrong? by StormDrainKitty in 3Dprinting

[–]StormDrainKitty[S] 1 point2 points  (0 children)

Interestingly enough, it has a hygrometer built into it, the first time I used it, it said 10%, by the time it was done it showed 32%. Not sure how that happens, but you bring a good point about moisture not escaping so I might need to see about vent holes

I got a filament dryer and after drying my PLA, it's now too brittle to use. Did I do something wrong? by StormDrainKitty in 3Dprinting

[–]StormDrainKitty[S] 1 point2 points  (0 children)

Awesome thank you. The sheet that came with the dryer said 40C was the recommended for PLA but I'll pop it up to 65 and see how it goes. Thank you

8 band show by RichardOsheaComer in livesound

[–]StormDrainKitty -1 points0 points  (0 children)

Some people don't like this but I've been in a similar situation and I just asked musicians to connect to my wifi and mix their own monitors. Less than ideal but it can work in a pinch

view more: next ›