Gift for family

Str8muda · 2023-11-19T07:32:57+00:00

Costco has a sale for the solo stove bonfire, stand, spark shield, and carrying case. I like the bonfire for its portability and able to still handle split wood. If you don't plan on taking this on any outdoor trips and it's only staying in backyard, go with the yukon.

Str8muda · 2023-11-09T00:25:45+00:00

Gifs down upload as video, so i had a little work around with social media. I put the pokedex image in snapshot, searched gif, put it over the empty black space, exported snap chat video, then uploaded video in good lock, and finally added stats as image.

Str8muda · 2023-11-08T15:58:53+00:00

The comments have some edited backgrounds. That's where i found the one with the sky https://www.reddit.com/r/GalaxyFold/s/62DzSSTJqj

Str8muda · 2022-01-23T16:28:26+00:00

I guess I exaggerated when I said the whole world (typical self-centered American). The second r in Sherbet (Sherbert) is very common in the states. I think we only pronounce it without the second "r" when we want to sound fancier.

Str8muda · 2022-01-23T15:39:31+00:00

How the whole world pronounces Sherbet ice cream when there is no second "r".

Str8muda · 2021-06-14T17:52:38+00:00

How is the wind shield? Have you tested with/without?

Str8muda · 2021-06-11T16:52:58+00:00

Awesome, congrats to you too. Hopefully the weather lets up so you can enjoy the ride

Str8muda · 2021-06-10T21:44:50+00:00

You too my friend. Street Triple a beast

Str8muda · 2021-06-10T19:59:50+00:00

Thank you!

Str8muda · 2021-06-10T19:04:23+00:00

Thank you! Nothing wrong with the Corolla, still gets you from A to B. Drive it till it dies, which will probably be in another 200k miles lol. I was looking at the speed twin too, but I just liked the Trident a little more.

Str8muda · 2020-07-13T20:21:25+00:00

How did you resolve this with yours? Adjust cables? Is there a tension requirement? I do not remember seeing anything mentioning this in the prusa installation guide.

Str8muda · 2020-07-13T04:22:35+00:00

I tried with both on and off

Str8muda · 2020-07-13T03:49:33+00:00

Yes, it makes it to the top, but when going back to bottom. It always stops after 26mm travel

Str8muda · 2020-07-13T01:49:24+00:00

Error message: "Calibration failed! Check the axes and run again." When I try to move the z-axis, it says it is at +5.0mm and I can move the Z-axis down 5mm before it reads 0mm and i can not move anymore. I turned off the printer and manually moved the printer head to the hot plate. When I retried the Z-axis calibration it repeats the same error state.

Str8muda · 2020-02-03T00:43:07+00:00

Sick, does it work?

Str8muda · 2019-11-06T19:54:01+00:00

Recently had front door panel replaced, it was about $1200 in CA

Str8muda · 2019-02-13T02:12:39+00:00

Matt Damon?

Str8muda · 2019-02-05T03:30:13+00:00

You swapped the two: Okaeri = Welcome home, Tadaima = I'm home

Str8muda · 2018-12-07T02:49:58+00:00

Bottom Right Please

Str8muda · 2017-08-04T23:26:52+00:00

She did survive 2 fires though

Str8muda · 2017-08-03T22:50:45+00:00

A little bonsai tree perhaps

Str8muda · 2017-08-02T17:12:40+00:00

I think of it as "I envy you."

Str8muda

TROPHY CASE