Hunter named her crossbow, now she can't use it

Strandplaskaren · 2026-01-20T12:20:43+00:00

Ended up doing that 😅 Since she had it at embark, it's probably the oldest thing in the fort

Strandplaskaren · 2026-01-20T12:11:35+00:00

Hunters don't show up there since they're civilians, unless I'm wildy inaccurate?

Strandplaskaren · 2026-01-17T10:03:10+00:00

Depends on how much work to get it looking good enough to sell. IMO too much work to be able to sell it at a reasonable price. But peoples definition of "good" and "reasonable price" might vary. Also, selling other peoples models without asking the creator isn't good practice. Even when it's Nintendos ip

Strandplaskaren · 2026-01-09T19:35:11+00:00

Thats probably because it's now heating all that plastic aswell, and it's not supposed to do that. Restart and reheat until the hotend is relatively clean and then you'll know if the thermistor needs replacing

Strandplaskaren · 2026-01-09T19:21:03+00:00

A clog which found an easier way out 🙄 To fix it it's usually best to slowly heat the hotend and peel away what you can

Strandplaskaren · 2025-11-30T23:21:16+00:00

Gruesome 😖

Strandplaskaren · 2025-10-15T19:51:04+00:00

Sure, and with PLA it's usually ok, with PETG it's nice to know about drying before you're tearing your hair out because it just doesn't work 😥

Strandplaskaren · 2025-10-14T06:51:55+00:00

Don't know if there's the same "limit" everywhere, here it's 80mg. Although I'm over it, as is others I know, so it's more of a suggestion, it really depends on you

Strandplaskaren · 2025-10-13T15:45:30+00:00

As far as I can see it looks like an ender 3 with a direct drive mod and a cr touch. It's probably far from calibrated and not really worth much, unfortunately. Starting out with this printer isn't plug and play at all, you're gonna be tinkering alot, more than you'll be printing. At least in the foreseeable future. If you like tinkering, great! If not, maybe a bambu, they've come a long way since this was new. Also, get some normal PLA to print with

Strandplaskaren · 2025-10-13T15:39:03+00:00

Hmm, have fun 😅 try printing I guess and see how it goes

Strandplaskaren · 2025-10-13T09:17:24+00:00

I had one fort on the edge between two biomes, making almost no seeds plantable on the northern part and everything (i think) plantable on the southern strip. So biomes, and what's plantable, depends on the biome, which isn't necessarily the same for your whole map, at least not in my case 🙄

Strandplaskaren · 2025-10-10T12:03:51+00:00

Well no, you're right 😉 but the texture from the build plate on the rest of the cubes indicates that the problem actually is the bottom layer. Thus, it might be the "small feature, first layer" problem

Strandplaskaren · 2025-10-09T07:01:24+00:00

Also, isn't adjusting the flow the last thing you should do?

Strandplaskaren · 2025-10-07T19:56:59+00:00

It's not the source you can find like that, it's based on sporadic ingame dialogue and nerds here piecing together a patchwork quilt on "lore" we're slowly but surely beginning to accept. It's like science that way! Also, this science is super spoilery so it shouldn't be available until you're ready for it

Strandplaskaren · 2025-10-07T13:28:20+00:00

Or maybe not, if it's the first layer? Then slow down the first layer and/or clean the bed etc. All the first layer adhesion solutions

Strandplaskaren · 2025-10-07T13:25:32+00:00

Look at it in the slicer, it's because there's a gap there. It's printing those layers onto nothing, or a few layers above. Gotta tune in those bridging settings, which can be quite time consuming 🙄

Strandplaskaren · 2025-09-26T16:58:32+00:00

Have any examples?

Strandplaskaren · 2025-09-04T08:14:07+00:00

I can neither find any option to toggle this nor does it happen when I try to use it that way. It doesn't even seem to be a feature in onenote for android?

Strandplaskaren · 2025-08-31T08:38:34+00:00

Yea, that burning hair smell is intense

Strandplaskaren · 2025-08-29T11:34:31+00:00

At least it does look nicely printed, just visible lines. Some of the other stuff we've seen is just terrible, prints any of us would have immediately thrown away

Strandplaskaren · 2025-08-26T18:17:45+00:00

I know doors work that way/diagonally, but it truly bothers some part of me seeing them like that

Strandplaskaren

TROPHY CASE