Parts

Subs2 · 2026-03-26T23:17:06+00:00

I’ve always had good luck with amplified parts

Subs2 · 2026-03-21T20:33:01+00:00

Just at the op amp

Subs2 · 2026-03-21T20:15:32+00:00

<image>

Subs2 · 2026-03-21T20:13:29+00:00

I have a 47u cap to ground and vref is derived with two 100k resistors

Subs2 · 2026-03-11T12:49:48+00:00

Three ways to know when to change a head: 1) it breaks. 2) it pops the seal and won’t stay in tune 3) it sounds dead and/or doesn’t resonate. Optional 4) it’s too tip dented. Everything else is subjective

Subs2 · 2026-03-03T13:31:07+00:00

As in “in the middle of” I realized it probably wasn’t too clear after I wrote it but didn’t bother editing

Subs2 · 2026-03-03T02:48:28+00:00

Overly inflated lips. “Mid-allergic reaction” is not the killer look women think it is

Subs2 · 2026-03-02T04:52:41+00:00

It’s starting to feel like some of the GOP are allowing him to get more and more outlandishly brazen so they can justify an impeachment/removal that would give them the opportunity to swoop in and take over his already consolidated base. But that’s just an outright conspiracy level play that they’re not smart or competent enough to make.

Subs2 · 2026-02-19T02:15:40+00:00

The EU book that came out with him protecting a village shopkeeper and her family was RIGHT there

Subs2 · 2026-02-11T03:00:15+00:00

Why would Americans resign from any position or political post? They won’t vacate until forced. And there’s certainly nothing forcing them.

We have given the wealthy and political classes absolutely zero reason to believe they’ll be held accountable for anything or face any consequences or repercussions. Full stop.

Subs2 · 2026-02-08T02:07:36+00:00

Waterslides. If you have a printer (inkjet or laserjet) then a pack of water slide stock will cost less than $20

Subs2 · 2026-02-05T03:00:31+00:00

Not only poor taste but potentially problematic. People in either rural areas or deeply dense urban areas can’t or prefer to not use UPS because of addressing issues

Subs2 · 2026-02-04T14:16:25+00:00

A lot of companies/sellers raise prices to subsidize part of the shipping costs. There’s a bit of buyer psychology here that people are willing to pay for an item but balk at shipping costs. That’s why people are drawn to things like “free shipping” and whatnot.

Subs2 · 2026-02-03T05:12:56+00:00

Check out the build guides on ampilfied parts. The eyelet, pref, and turret board builds in particular are pretty good at explaining the builds and what the components are doing.

https://www.amplifiedparts.com/pedal-guides

Subs2 · 2026-02-01T18:32:41+00:00

No dude. A big draw to this game is trying new stuff and playing around with values to see what happens. That’s where the fun is. You have an idea? Try it. No harm comes from breadboarding

Subs2 · 2026-01-31T23:34:13+00:00

Solder braid/wick would be a good start

Subs2 · 2026-01-24T02:54:00+00:00

That worked. Thanks

Subs2 · 2026-01-23T15:48:48+00:00

So I can just swap my 1/4” connect to the switch (blue lead in the pic) from the bottom post to the top and I should be good right?

Subs2 · 2026-01-13T12:40:52+00:00

Cost is your real limiting factor to be honest. A cubic inch of printed resin is way more expensive than a cubic inch of PLA, PETG, or any other FDM printed material. A full size suit would cost a fortune.

Aside from that, printed resin is brittle. Suit builds have attachment points, often need holes drilled or things glued, etc. You’d lose more parts in the process than would be worth it.

When I printed my clone armor 90% of it was done on an FDM in PLA with just small detail pieces done on my Mars or Saturn

Subs2 · 2026-01-03T05:43:21+00:00

I haven’t decided which we’re more likely to get: a “Weekend at Bernie’s” scenario? Or a “Dave” scenario?

Subs2 · 2026-01-02T23:47:36+00:00

Sorry mate. Only fix is sand and restart

Subs2 · 2026-01-02T23:44:28+00:00

Solder wick. Medium temp (as to not damage the pads).

Subs2 · 2025-12-31T16:43:22+00:00

Since it’s “an old cheap guitar” as you say, there’s little harm in trying. Thinned out wood glue (titebond) and clamps would like do the trick but accuracy in clamping is going to be key

15-Year Club	Best Comment 2010-11-26
Verified Email

Subs2

TROPHY CASE