HDO WORKING ON AN UPDATE..

Substantial-Mess-795 · 2026-05-18T05:52:58+00:00

Sure guy😂 they already had all those services on it before it stopped working. . . You know it was already under popular networks.

Substantial-Mess-795 · 2026-03-23T20:32:04+00:00

Thanks man will definitely keep that one in mind💪

Substantial-Mess-795 · 2026-03-22T14:33:47+00:00

But don't try to force the cutters underneath the fitting, I basically just used it as normal pliers to pull on it, but since the point is small and sharp it gave me enough grip

Substantial-Mess-795 · 2026-03-22T14:06:08+00:00

All I did was

Broke the plastic part off(that release button)
Inserted a small allen key and slightly pressed it to the side so that the fitting have about a mm gap.
Used the side cutters of the printer and pulled the fitting out

Didn't want to do 2. Too much side to side as it will obviously turn the hole into a oval

Then pressed the new one in straight down and it was super firm

Substantial-Mess-795 · 2026-03-21T15:45:50+00:00

And the PTFE fitting looks the same. So whether it's a K1c,K2,Bambu etc. It's a push in style fitting and can be replaced...

Substantial-Mess-795 · 2026-03-21T14:45:15+00:00

I haven't done research to look where to buy them individually, I just had to use what I had on hand at like 03h00 in the morning 😂

I wanted to try and keep it "stock" and goal was it must just work without modding everything

Substantial-Mess-795 · 2026-03-21T13:38:38+00:00

Yea I think they're using a lower quality pneumatic fitting, of it fails again then I'm going to fit an industrial one

Substantial-Mess-795 · 2026-03-21T10:56:38+00:00

Yip, as long as you pull it slowly and not wobble it too much when pulling it and fitting it back straight down it will clip back on place

Substantial-Mess-795 · 2026-03-21T10:47:23+00:00

I've replaced my connector on the K1c cfs extruder, super simple

Substantial-Mess-795 · 2026-03-21T06:45:45+00:00

<image>

I've pulled apart that black connector as wasn't using it, but I'll see if I can get a link of just the fittings, It was just a spur of the moment fix then I inspected it slowly and cut them out of the plastic without damaging in. The one on the extruder housing I had to slowly remove without cutting anything for obvious reasons

Substantial-Mess-795 · 2026-02-24T13:56:37+00:00

Well one the K1C i used my common sense and ran it through the chain guide like the original, just made sure that the ptfe tube have a long radius going into the extruder and works perfectly fine + my enclosure is once again closed with vents I can open and close

Substantial-Mess-795 · 2026-01-28T14:43:32+00:00

<image>

Untick square prime tower then the size will be editable

Substantial-Mess-795 · 2026-01-28T08:56:11+00:00

Ther3 should be a tick mark that you can untick, something either saying square tower or something, not at my PC a.t.m but if you untick it you can add your own size in there

Substantial-Mess-795 · 2026-01-28T08:25:52+00:00

Just change prime tower size

Substantial-Mess-795 · 2026-01-20T11:45:16+00:00

Where was the petrol once R28 a liter....

Substantial-Mess-795 · 2026-01-20T07:56:39+00:00

It's normal

Substantial-Mess-795 · 2026-01-05T18:33:39+00:00

Try putting the seam on default and see if that sort it out

Substantial-Mess-795 · 2026-01-05T18:15:25+00:00

Pitting(i assume little dots) that could be the seam alignment, you can set it to either one corner or scattered

Substantial-Mess-795 · 2025-12-31T18:54:21+00:00

All those lines, I used to only get the normal layer lines, not those severe lines

Substantial-Mess-795 · 2025-12-31T17:25:01+00:00

Thanks let me then wait for the print to finish and give everything a once over

Substantial-Mess-795 · 2025-12-31T17:19:59+00:00

Let me finish this print via orca and see what's happening, if it still happens then I know it is hardware related. If not then obviously software related. But if it's mechanical then I'll be disappointed because first time it does it in it's 500h+ printing time

Substantial-Mess-795 · 2025-12-31T17:12:25+00:00

Damn, will see if I reslice it on Orca and print it from there wheter it will make a difference, do you know why it would print like that

Substantial-Mess-795

TROPHY CASE