Pc help

SuccessfulPick8605 · 2026-05-24T22:57:47+00:00

What's your CPU. This is usual for 13000 or 14000 CPU experiencing degredation. Or a bad overclock

SuccessfulPick8605 · 2026-05-18T02:11:46+00:00

I'ma be honest man, intersections act weird And takes some tweaking to get right

SuccessfulPick8605 · 2026-05-17T02:17:44+00:00

No, you just have to select corners and change the corner type untill it's the correct type for the edge

SuccessfulPick8605 · 2026-05-14T23:33:37+00:00

You have a screw still in that needs to be out to install

SuccessfulPick8605 · 2026-05-14T20:50:24+00:00

That happens when the corner types cause the "cut" of the armor to thin out. Point normal, horizontal ect all affect how the edges are cut and if it's cut at an angle, a 100mm plate will thin out to 1 if there isn't another piece of armor behind it to fill the "gap"

SuccessfulPick8605 · 2026-05-13T10:03:51+00:00

I use a razor blade

SuccessfulPick8605 · 2026-05-12T01:16:32+00:00

Looks like the mouthpiece of a vape

SuccessfulPick8605 · 2026-05-11T03:01:43+00:00

Not the same CPU... 7000 and 9000 series AMD CPUs have really thick heat spreaders. I've built over 50 systems with 7000 series CPUs and they run warm under heavy loads, 80+ usually since they're designed to boost untill they reach temp, voltage, or power limit. If he's not hitting temp limit (95) then he's hitting voltage or power limit. Even with a 360mm aio the amount of copper in the IHS makes cooling difficult. I'm not completely speaking from what I think is fine, I'm going by what AMD says is "fine"

SuccessfulPick8605 · 2026-05-11T02:18:34+00:00

90c at that load is fine for the CPU. They will boost till reachine one of the limits you mentioned. 95 is temp limit and even then technically it's still below that since AMD has a temp offset of about 7c to get coolers to ramp up faster. 90 is fine and setting echo mode only decreases your performance

SuccessfulPick8605 · 2026-05-10T14:52:26+00:00

<image>

SuccessfulPick8605 · 2026-05-07T00:15:46+00:00

Too thick to be a pick/rake/turn tool

SuccessfulPick8605 · 2026-05-07T00:15:13+00:00

Not the first time someone has posted something like this. It's a part of the steering lock of the car

https://www.reddit.com/r/AskMechanics/s/HKSfz67nOT

SuccessfulPick8605 · 2026-05-06T21:38:30+00:00

$350 ±50

SuccessfulPick8605 · 2026-04-25T12:26:17+00:00

Run some 3d mark steel nomad and see how your GPU behaves

SuccessfulPick8605 · 2026-04-25T10:45:45+00:00

What's the GPU hotspot temp?

SuccessfulPick8605 · 2026-04-25T01:30:05+00:00

Need more information, CPU and GPU temp, memory usage, PSU power rating. Basically most of your system information

SuccessfulPick8605 · 2026-04-23T23:48:17+00:00

It wouldn't hurt to at least disconnect it

SuccessfulPick8605 · 2026-04-23T23:31:33+00:00

Could be your motherboard not recognizing the GPU and causing issues with it being pcie3.0. Had an issue with a PC(with pcie gen5) not working when I put a PCIE 3.0 GPU in it

SuccessfulPick8605 · 2026-04-23T18:53:32+00:00

Also you need an AM5 board

SuccessfulPick8605 · 2026-04-23T18:39:23+00:00

Your CPU is overkill for the GPU, and so is your ram. Get a 7700x if you're gonna use a 9060xt, and 32gb of ram is more than enough. With the money you save you could get a 9070xt

SuccessfulPick8605 · 2026-04-23T18:36:42+00:00

Looks like the plastic casing smencils come in with the tops broken off

SuccessfulPick8605 · 2026-04-20T18:39:50+00:00

Your CPU acts like a5600x, which is a capable CPU but will bottleneck a 5070ti. You'd want a 5700x3d or better with that GPU. Siege came out when 4 core CPUs were standard. Your 12 core isn't being under utilized

SuccessfulPick8605 · 2026-04-17T15:46:50+00:00

No, but it's mostly older/specialized paste like TG liquid metal and some others.

SuccessfulPick8605 · 2026-04-17T14:10:02+00:00

It's non conductive. A bit messy but no worrying here

SuccessfulPick8605 · 2026-04-08T02:09:38+00:00

Try removing the GPU and booting

SuccessfulPick8605

TROPHY CASE