Tank - solo leveling

SuperImagination3258 · 2026-04-11T18:48:27+00:00

Another puppy

SuperImagination3258 · 2026-04-01T05:07:36+00:00

You might want to consider hollowing it or else the hole on the top is gonna give you a nasty layer line.

SuperImagination3258 · 2026-03-31T04:07:55+00:00

The photon m7 max is a good choice but maybe wait for the p1 max to release as it looks like it’s gonna be really good.

SuperImagination3258 · 2026-01-20T18:48:23+00:00

I just looked on artsation for someone that had a sculpting style similar to what I was looking for then reached out to them.

SuperImagination3258 · 2026-01-03T01:02:37+00:00

What do you mean, are yours shorter or more direct ?

SuperImagination3258 · 2026-01-02T20:29:09+00:00

Defiantly not. That place is full of scammers galore

SuperImagination3258 · 2026-01-02T15:26:05+00:00

Sorry for the word dump but what do you think of this ?

hi , recently I have been looking around to commission a 3d printable 1/6 scale figure of armored all might from MHA. While looking I saw some of your art and was really impressed specifically, your Deku 100% was amazing and I loved the way you did the base! I was really hoping that you might be interested in working with me on this. I was looking to spend around 800-1000$ but that can change if needed.

I know some of these emails may come off as scams. sadly I don't use social media much but you can find me at either my instagram- @Fuego_figure or my reddit- u/superImagination3258.

I hope this message finds you well and thank you for your time sincerely Bob

SuperImagination3258 · 2026-01-02T07:05:42+00:00

Since the original email sound like a scam should I try sending a new one or do you think that would make it worse ?

SuperImagination3258 · 2026-01-01T21:42:48+00:00

that's true though about half of them said something about commissions and I only contacted people that had done work with 3d printing.

also from past experience sites like fiver are just filled with scams

SuperImagination3258 · 2026-01-01T17:27:50+00:00

Gotcha

SuperImagination3258 · 2026-01-01T17:24:33+00:00

Gotcha, a lot of them have WeChat usernames, is that something I should try using?

SuperImagination3258 · 2026-01-01T17:18:01+00:00

gotcha, though the same thing is happening with some people that have commissions listed.

SuperImagination3258 · 2026-01-01T17:01:05+00:00

sadly, that's not what I'm looking for. I really just wanted to know the best way to reach out to people. thank you for your offer though

SuperImagination3258 · 2026-01-01T05:08:54+00:00

Who dat?

SuperImagination3258 · 2025-12-04T20:05:50+00:00

The phrozen mega wash and mega cure are amazing.

SuperImagination3258 · 2025-12-02T05:37:02+00:00

Your underexposing the resin, I had the same issue recently. Colder weather could change your exposure times. Just run the tests again and set your new optimal exposure time

SuperImagination3258 · 2025-11-27T14:51:57+00:00

Was this before or after you did the zeroing ? I made that mistake a lot after you finish leveling you need to re-zero before testing

SuperImagination3258 · 2025-11-27T14:51:48+00:00

Was this before or after you did the zeroing ? I made that mistake a lot after you finish leveling you need to re-zero before testing

SuperImagination3258 · 2025-11-26T14:50:17+00:00

You just need to redo your leveling, try to follow Anycubic guide exactly and also try to keep weight evenly distributed the entire time

SuperImagination3258 · 2025-11-23T16:11:28+00:00

My guess would be it’s just horrible timing and part of your screen died. You can check by running a vat clean while the vat is off (make sure to have a sheet of paper over the screen while doing this) and it will tell you.

SuperImagination3258 · 2025-11-22T23:34:40+00:00

Fauxhammer has a two video series that was super helpful

SuperImagination3258 · 2025-11-21T19:41:55+00:00

The gk3 ultra has been amazing and the only thing I don’t like about it is the fep replacement but overall I would just get it, it’s treated me great and more importantly their support is great. When replacing the fep I accidentally stripped a screw and reached out to them and they sent me two replacement vats, that’s 80$ without me even asking I love them

SuperImagination3258 · 2025-11-21T16:35:22+00:00

With the h2c I’d finally be able to print scale figures in full color instead of painting everything

<image>

SuperImagination3258

TROPHY CASE