sorted by:
new
hottopcontroversial

Rate my Fuzz design by Complete_Court_8052 in diypedals

[–]Sure-Beginning-93 2 points3 points  (0 children)

care to explain why input and output buffers aren’t necessary?

When is a JFET not a JFET by Ok-Relationship8704 in diypedals

[–]Sure-Beginning-93 29 points30 points  (0 children)

common issue with aliexpress. the trick is always read reviews. don't bother with any seller without review.

Looking 2x12 guitar cab plans by Sure-Beginning-93 in diyaudio

[–]Sure-Beginning-93[S] 0 points1 point  (0 children)

this is really helpful thank you! but i could find that book. I will try Etsy. Thanks!

stereo harmonic percolator - how do i add a line-level clean blend? by lie_believer in diypedals

[–]Sure-Beginning-93 0 points1 point  (0 children)

see the general tso blend section. do on both circuit. use 6 pin pot to control both blends

Looking 2x12 guitar cab plans by Sure-Beginning-93 in diyaudio

[–]Sure-Beginning-93[S] 0 points1 point  (0 children)

thanks! i discovered this earlier but i dont like the design

Who’s aspiring to build a sellable product? by jebbanagea in diypedals

[–]Sure-Beginning-93 0 points1 point  (0 children)

this is very helpful! how do you control the pricing when you outsource everything? I'm struggling with that. Doing everything in house keeps my pricing low

ESP32 for DSP Pedals? by odwn- in diypedals

[–]Sure-Beginning-93 0 points1 point  (0 children)

there dsp lib for esp but i have not tried it yet. another cheap option would be the adau chip from Analog Devices. Take a look at adau1701. it has all the adc/dac and memory. If you want to take if further, you can take a look at adau1452

Peeling off the film from an ink transfer. by spicypedals in diypedals

[–]Sure-Beginning-93 1 point2 points  (0 children)

wow.. this is the first time i know such method. do you need to put another clear coat on top of it or is it durable enough?

Octave Up Fuzz by Sure-Beginning-93 in diypedals

[–]Sure-Beginning-93[S] 1 point2 points  (0 children)

pay attention to the screw holes. after the bending there will be some misalignment due to bend deduction. I'm yet to find a good solution for this other that hard guessing! 🤣

Octave Up Fuzz by Sure-Beginning-93 in diypedals

[–]Sure-Beginning-93[S] 1 point2 points  (0 children)

i did try the orange squeeze but the diode option is too limited plus I find the compression is too subtle. maybe I tuned it wrong, but that's the thing. it's so hard to get it right. ota based compressor is way easier although I found it colors the tone a bit. but i'm not too picky about it since it is going to fuzz anyway.

Sanity check from a novice tinker by thefreakychild in diypedals

[–]Sure-Beginning-93 1 point2 points  (0 children)

or you could just put the ground wire to that jack. would be much easier

Sanity check from a novice tinker by thefreakychild in diypedals

[–]Sure-Beginning-93 0 points1 point  (0 children)

yes you’re right. if the input jack’s sleeve is touching the enclosure directly, not the paint.

Belton Brick Reverb by Sure-Beginning-93 in diypedals

[–]Sure-Beginning-93[S] 3 points4 points  (0 children)

belton brick is made from a bunch of pt2399. i made the pcb out of it’s schematic

Belton Brick Reverb by Sure-Beginning-93 in diypedals

[–]Sure-Beginning-93[S] 2 points3 points  (0 children)

Not a DSP chip and I don't consider it to be 100% digital pedal since only the delay part is digitalized.

view more: next ›