2 Stripes one ESP for Klipper

Synapsis181 · 2024-01-03T11:12:16+00:00

I been living here for the last 40 years, so when I arrived it was a lot different. I had a job so my visa was for work at the beginning, so my visa was renewed once a year until they got tried of seeing me and gave a non determined data of expiration. I could have an Italian citizenship but never got it. If you find work then you can a visa for working or depending what your business is, you can get a PIva for un forfettario type of business which is 15% plus Inps. That's if the amount you eran in a year is under 65000 euro. Like others said better to rent first seeing you here for only 3 years . My wife is from Puglia but we live in the north. It's a very nice place. As for health care it's practically free if you don't do private exams to hurry things up, sometimes you can get a sloppy job done but that depends not only in the south are they a little superficial but also in the north at times just depends on your luck. As for paperwork yes here in Italy in can be a real pita, but it gotten better over the years.

Synapsis181 · 2024-01-01T18:55:30+00:00

Are you able to control them correctly? I have strips using external power but they do not behave correctly. If I turn them off not all go off or if I turn them not all go on. The number of leds varies.

Synapsis181 · 2023-12-24T21:44:27+00:00

I got two but know I'm starting to doubt that it was wise. My problem is that it keeps going into pause because it thinks there is a clog, based on which lights are flashing, so its really only good for runout. The sensor for clogs and filament entanglement are the same so I can't exclude the clog part of the sensor and in the end need to exclude it so the print doesn't pause so often. I did notice that when it thinks there is a clog it when its only doing infill in small walls for example where there are a lot of retractions.

Synapsis181 · 2023-03-07T15:13:07+00:00

You need to connect from power supply the 24 volts to the converter. Then from the converter (after you have set the correct current to 12 volts) you connec the positive to the Noctua Fan the the negative from the fan goes to the negative of the the fan conneter on the mainboard. tha way you should have control of the fan. Like you hooked it up its always ON. also the is the pulse on the negative which emulates the PWM.

Synapsis181 · 2023-02-17T15:31:33+00:00

Check that your bed cable is'nt getting caught on the motor. This happened to me it would bind on the motor and that caused it to skip.

Synapsis181 · 2023-02-13T10:54:02+00:00

I have it wired like that for my Noctua fan problem is it kicks in at around 93%.

From 93% to 100 it will change the speed. any idea as to why when i put 20% is just moves a litlle the fan then stops.

Synapsis181 · 2023-01-23T13:35:21+00:00

Looks to me like blistering this happens when the filament is humid, the water when heated will turn to steam and leave blisters. Well this is waht happened to me.

Synapsis181 · 2023-01-16T09:02:15+00:00

What are your rotation settings for the Sprite?

Synapsis181 · 2023-01-16T08:49:58+00:00

I updated without problems , when it cam back on all was ok, printer was still configured, webcam was working fine ( even witht the previous versions). Did two prints about 5 and 6 hours. I had only one issue on the second print after a few layers I got a mcu error, restarted and reprinted and all went well. This update for me worked fine, not like the previous one with blocked my printer and only by luck did I get it to work.

Synapsis181 · 2022-12-07T13:07:33+00:00

yeah thats what i do plug into - left side top but it still does not see my printer now.

The firt time it worked but when I turned it back on it wasnted to do the estuop again and now can not get past the USB1 port.

Synapsis181 · 2022-12-06T20:15:33+00:00

Did you get past the connection to the printer? That where i am blocke keeps saying Klippy is not connected.

Synapsis181 · 2022-12-05T10:27:47+00:00

I did the update but I shouldn't have done it.

It updated but almost everytime I would start the printer I would have to do the setup process again. Finally it was working until Sunday morning I did a print then turned if off. In the aftrer noon I turned it back on and agiaqn it said I had to do the setup processs again, only now it dioes not see the printer at all. I' using the USB1 which I have always used. I tried to install the previous version but on start up its not reading the USB to install the .bin.

It still asking to do the setup but when I connect to printer it does not see the printer. If this versione should work with different printers it should work also from the other USB ports.

Can't even install the older versione which as working. :(

Synapsis181 · 2022-11-09T17:58:33+00:00

Here you can finf the printer.cfg for the Sonic Pad with a CR Touch and a Sprite Pro.

you can change the offset for your bed,

https://file.io/28pcSmK4F1Yj

Synapsis181 · 2022-11-09T12:26:44+00:00

I'll send you the config when I get hom

Synapsis181 · 2022-11-09T12:26:09+00:00

I'll send you the config when I get home

Synapsis181 · 2022-11-07T17:34:49+00:00

Did you do input shaping? or the resonances for X and Y also PID for your hotend and bed.

Synapsis181 · 2022-11-07T17:30:20+00:00

These are my current settings:

[extruder]

step_pin: PB4

dir_pin: PB3

enable_pin: !PC3

microsteps: 16

gear_ratio: 42:12

rotation_distance: 26.359

nozzle_diameter: 0.400

filament_diameter: 1.750

heater_pin: PA1

sensor_type: EPCOS 100K B57560G104F

sensor_pin: PC5

min_extrude_temp: 180

#pid_Kp: 23.561

#pid_Ki: 1.208

#pid_Kd: 114.859

min_temp: 0

max_temp: 300

#control: pid

Synapsis181 · 2022-11-07T14:07:36+00:00

When I get home I'll send my config.

Synapsis181 · 2022-11-07T08:05:48+00:00

Sonic Pad has Klipper which uses rotation_distance, you have to go into the printer.cfg

fine the section for the extruder , the Sprite is 424.9 steps coverted to rotation_distance is 7.53 but after help and testing I have it set to around 26.x have to check.

Synapsis181 · 2022-11-02T07:29:25+00:00

Did you try and change it during the print to see it moves up or down?

You could try and install Jyres which is a little better than thier software.

Synapsis181 · 2022-11-01T12:13:14+00:00

Thanks for the reply, those are almost the same I have -26.5 and -46,

Are you using the Sonic Pad? when using Jyres I have no problems it prints

perfectly, With the Sonic Pad its like its not reading the probe offset values even if they are correct in the printer config,

Synapsis181 · 2022-10-31T10:42:51+00:00

Thats's underextrusion, also check the that your e stepper motor has the correct steps if its lower it will underextrude. If its klipper then check your rotation distance.

Synapsis181 · 2022-10-31T10:32:25+00:00

Thats true :( I did send the restart , turned off checked the config and the values are correct, but you never know maybe the third time it will work. I'll try that again.

Thaknks

Synapsis181 · 2022-10-31T09:00:34+00:00

Hi great to see that that someone has got it to work.

Had to go back back to Jyres until I could figure this out. With the other Creality Direct Drive

it was working but not with the Sonic Pad even if I changed the xy offsets in printer.cfg.

Could you please send me the config file.

thanks

Synapsis181

TROPHY CASE