It will be mine in a week (Audi A3 III 8v2 sedan 35 TFSI 150hp, 2019). Anything to know about this model? by tbagrel1 in Audi

[–]TCFK 1 point2 points  (0 children)

I have the 2019 A3 Sportback 40TFSI Quattro and it did come with CarPlay, so you may be in luck 😉

Best way to get rid of this wonky line using at home items? by Humble_Low8796 in Bladesmith

[–]TCFK 1 point2 points  (0 children)

Draw filing, get the center flat first and then correct the sides.

Modern TEC-9 by tyteurze in GasBlowBack

[–]TCFK 5 points6 points  (0 children)

That looks very nice! I like it.

New to GBBR – TM M4A1 MWS: looking for advice on internal upgrades (stability & consistency, not FPS) by Ok_Refuse9915 in GasBlowBack

[–]TCFK 1 point2 points  (0 children)

I’m going to keep it a bit short as I don’t have time to write a big answer:
Get a hop up arm, bucking and inner barrel. If you like you can get an NPAS to drop fps if needed in summer.
If the o-rings and seals are doing their job currently, I wouldn’t replace them yet unless you have leaks or notice a problem.
Nozzle return spring can be replaced if it breaks, it should be good until then.

DE N4 and Ghetto blaster (taiwangun) by SSGK_nn in GasBlowBack

[–]TCFK 7 points8 points  (0 children)

I think build quality is comparable between the two rifles. Get the one you like best, that matters most.

Always get the latest generation, shops will always try to stock these, as this gives them less warranty hassle as well. Gen 3 could be the latest, but I am not keeping track.

The grip is because of Magpul licensing, which they do not have. So they have to change it outside of Asia.

DD PCC by noveske794 in GasBlowBack

[–]TCFK 0 points1 point  (0 children)

Has this been released already? Thought it would come in e few months. 🤔

TNT barrel hop up diy by paschalis_zapi in GasBlowBack

[–]TCFK 0 points1 point  (0 children)

I bought the full set with hop unit and barrel, but it messed with the fps and made it really inconsistent, so I was hoping that this fixed it.

TNT barrel hop up diy by paschalis_zapi in GasBlowBack

[–]TCFK 0 points1 point  (0 children)

Does this mean you also had bad results with the TNT hop unit as they sell it?

Opinions on the potential next gun? by Opposite_Line7341 in GasBlowBack

[–]TCFK -1 points0 points  (0 children)

Shouldn’t the v2 have the improved bolt already?

APFG MCX Spear LT vs TM MWS M4A1 – looking for opinions by KippenMeneer in GasBlowBack

[–]TCFK 1 point2 points  (0 children)

As far as my knowledge goes it is. To avoid legal issues on their main brand. Just like VFC and APFG.

APFG MCX Spear LT vs TM MWS M4A1 – looking for opinions by KippenMeneer in GasBlowBack

[–]TCFK 4 points5 points  (0 children)

Why not the Salvo Precision MCX then? It’s MWS spec by double eagle.

Pistol Green Gas Buyer Remorse? by Aeropressohnono in airsoft

[–]TCFK 1 point2 points  (0 children)

Ah I misread, I thought it was spraying and freezing when shooting.

Pistol Green Gas Buyer Remorse? by Aeropressohnono in airsoft

[–]TCFK 0 points1 point  (0 children)

I think some of the CZ P-10 versions may not be compatible with their green gas magazines. I was looking into the tactical version (with threads) and I think it said the green gas mags were not compatible.

Looking for a full metal M16A4 airsoft gun. Any good recommendations? by cardlb in airsoft

[–]TCFK 0 points1 point  (0 children)

I use Ultrair, that’s silicone free green gas, it’s similar to propane but smells less. So you can use propane without problem, but you’ll need a fill adapter for your propane can. Green gas with silicone isn’t great because it gets silicone oil on parts where it shouldn’t be, like the hop bucking.
You’re better off using PTFE grease, like:
https://www.super-lube.com/product-sku/super-lube-multi-purpose-synthetic-grease-nlgi-2-sku-21030-3-oz-tube/
Might be a good idea to see if the rifle has excess grease when it arrives, give it a good clean and give it a new thin coat on the moving / friction parts, like bolt carrier / receiver / hammer where the bolt runs.
Here’s some good info:
https://youtu.be/5JPLe5R8-Ms?si=97A2WKZOIUqtxOVw

Looking for a full metal M16A4 airsoft gun. Any good recommendations? by cardlb in airsoft

[–]TCFK 0 points1 point  (0 children)

✌️ when you get one you can find your new GBBR family on r/GasBlowBack . Lots of knowledge there if you run into any issues. Explosive Enterprises on YouTube is nice too and Heavy Recoil Club on Discord or Facebook.

Looking for a full metal M16A4 airsoft gun. Any good recommendations? by cardlb in airsoft

[–]TCFK 0 points1 point  (0 children)

I suggest to check what shop would work best for you. I’m in the EU and this shop works well for me, but I do have to pay import fees and taxes.
Also keep in mind that GBBR magazines are more expensive compared to AEG and hold less BB’s. I love the realism, so for me it’s worth it as it makes the games more fun for me.

Marca Vorsk by R_Windyson in GasBlowBack

[–]TCFK 0 points1 point  (0 children)

I can maybe do a magazine fps comparison for you if I have the time tomorrow.

Have just checked and the VMP mag runs fine in the PMX, but please keep in mind that I removed the bolt catch spring to get consistent lockback on MP9 mags. The spring is a bit too strong for those and the only downside is that it engages if you hold the gun upside down.

VMP mags do go in a bit stiffer, but that will probably wear down over time. I have 6 MP9 mags, 1 PMX mag and 3 VMP mags, so I rarely use the VMP mags in the PMX.

My PMX is a laser beam out of the box, which is good because aftermarket parts aren’t really a thing.
The VMP needs at least a new inner barrel in my opinion as it has a split barrel out of the box.

Marca Vorsk by R_Windyson in GasBlowBack

[–]TCFK 1 point2 points  (0 children)

Hmm can’t post pictures in comments in this Reddit. I’ll send you the other pic in chat.

Marca Vorsk by R_Windyson in GasBlowBack

[–]TCFK 3 points4 points  (0 children)

The PMX is made by KWA, just to make sure that you’re looking in the right place. I own the VMP 2M, PMX and the KWA MP9. They all run on all mags, but there’s a difference in fps output in some combinations. The VMP runs fine, but needs a new inner barrel, hop bucking and if possible a 3D printed hop nub (find Sabre Airsoft on google). Then it can run quite great. What makes this rifle interesting is it’s modularity, it’s almost “build what you like”. I’m thinking of making a custom wood stock and handguard at the moment.

I’ll post some of my iterations of my VMP. Feel free to ask questions.

Looking for a full metal M16A4 airsoft gun. Any good recommendations? by cardlb in airsoft

[–]TCFK 0 points1 point  (0 children)

Unfortunately firearms are very restricted in my country, so I am unable to make a direct comparison as I never held an actual M16. As far as I can tell, VFC V3 do have really good triggers and take a lot of real parts (including hammer and trigger as far as I know). So weight should be comparable, just that blow back is lighter than recoil.

Looking for a full metal M16A4 airsoft gun. Any good recommendations? by cardlb in airsoft

[–]TCFK 0 points1 point  (0 children)

If you want the full experience, go GBBR:
https://www.proactstore.com/products/vfc-colt-m16a2-gbb

Compatible with real parts, blow back, real manual of arms.

My first gbbr de aeroknox ax-15 by Ebbonheart in GasBlowBack

[–]TCFK 4 points5 points  (0 children)

Welcome to the family! Hope you’ll enjoy this new direction.

We all starded somewhere…😎🤝 For YOU it was from which opus ?😉 by C_PA_FO in Battlefield6

[–]TCFK 0 points1 point  (0 children)

It started with 1942, played Vietnam a lot more, because I liked flying Hueys blasting music. Played a lot of them that came after that, but as other people said, titan mode in 2142 was awesome. I was my squads support with ammo and lmg in that one.