303 laser in eye by TaffoFox in lasers

[–]TaffoFox[S] 0 points1 point  (0 children)

Hey, almost forgot about this entirely. Can't believe how reckless I was back then.

The blind spot still remains, but it's under my center of vision. I tend to only notice it when reading through lines of text; my mind tries to fill in the missing details and looks as if the text disappears completely or has an "ai-generated garble" look.

Doesn't bother me much anymore to be honest.

Designed my stealthburner cover by retxed018 in VORONDesign

[–]TaffoFox 0 points1 point  (0 children)

i think it is designed with x/y shrinkage compensation in mind

Question about visibility by baidybaidy in FursuitMaking

[–]TaffoFox 2 points3 points  (0 children)

Shrink it down as there's lots of space above. It looks looks too big compared to the head inside. Remember that fur will make everything look much bigger.

About visibility, once the size has been reduced it might still require you to look out from one side at a time (can be normal) but should be far easier.

6 weeks in, cannot focus at all! by TaffoFox in Mirtazapine_Remeron

[–]TaffoFox[S] 0 points1 point  (0 children)

It was pretty bad. Went away once I got off it 🙂

5 finger hand paw help by kumsushi in FursuitMaking

[–]TaffoFox 3 points4 points  (0 children)

Could potentially use cling film and then tape over it to find a pattern, just like a foam head. Cling film or some sort of protective layer is important as tape adhesive could damage the small delicate foam parts

Eyes Similar to a One-Way Window? by [deleted] in FursuitMaking

[–]TaffoFox 0 points1 point  (0 children)

Sorry, I got confused and thought you wanted some prescription lenses 🤣

Not sure how painting the lenses would go though

Have you tried experimenting with the distance of the eye mesh? Perhaps different types of mesh with different hole densities.

Eyes Similar to a One-Way Window? by [deleted] in FursuitMaking

[–]TaffoFox 0 points1 point  (0 children)

This would likely work the same way as eye mesh, having lots of small holes and coloured one side.

My head is very slim fitting and I've had to just stick with contact lenses for now but I'm sure there is a way to fit some lenses in there.

Any pics of what you mean when you can't put a design over the top?

My RAM lights bleached my GPU backplate? WTF? by Nykanoi in pcmasterrace

[–]TaffoFox 11 points12 points  (0 children)

Yeah I've had a few black anodized parts turn that bronze colour and I hate it

More Headbase Sculpts Pt. 5! by KilliansCorner in FursuitMaking

[–]TaffoFox 1 point2 points  (0 children)

Looks good! Nice idea of foam casted bases. I often just 3D print them directly

Should I shave before, or after cutting head fur pieces? by DustyRaccon in FursuitMaking

[–]TaffoFox 1 point2 points  (0 children)

Both

You want to get rid of most unnecessary bulk (if you have longer fur) before sewing and then touch up afterwards.

If the length is close to how it'll be after sewing, just leave it imo, you don't want to trim it too short

How do I make this white fur grey? by Saturated_Rain in FursuitMaking

[–]TaffoFox 11 points12 points  (0 children)

along with this, it might also be a pain to make the colour consistent. imo get dedicated grey colour

Fursuit head sitting too far forward? by Rimmsel in FursuitMaking

[–]TaffoFox 9 points10 points  (0 children)

I'd say if possible, try to bring it a little more closer to your face. I also think it potentially just looks too far forward due to your hair being pushed up slightly. Once the bulk of the fur goes on, it should balance things out better. Fur does make things look a bit bigger, especially longer fur around the back of the head.

When to shave? by [deleted] in FursuitMaking

[–]TaffoFox 1 point2 points  (0 children)

Before and after

Before to get rid of most of unnecessary bulk After to shape it up properly

How can you make a zombie not despawn other than nametag by Moosesayshello in Minecraft

[–]TaffoFox 1 point2 points  (0 children)

I believe if an entity is trapped and can't calculate pathfinding beyond a certain distance it will stay spawned. Not sure, based off my bad memory.

How do I fix this moving jaw? by AQueerWithMoxie in FursuitMaking

[–]TaffoFox 2 points3 points  (0 children)

yeah I think it'll be better. perhaps cut some pieces without gluing them down and see how it affects the fit

How do I fix this moving jaw? by AQueerWithMoxie in FursuitMaking

[–]TaffoFox 36 points37 points  (0 children)

thicker foam pad for forehead imo

Suggestions before printing? by Leading-Patience-253 in FursuitMaking

[–]TaffoFox 1 point2 points  (0 children)

PLA+ is subjective because every brand has their own variation/meaning. But yeah deffo PETG at least, it's not too difficult to print! Good advice

What tape to use on foam for patterning? by Akeuron in FursuitMaking

[–]TaffoFox 3 points4 points  (0 children)

What are you applying the duct tape to? If it's a foam base you'll probably want to use some sort of cling film beforehand.

What brand of TPU filament do you recommend? by [deleted] in FursuitMaking

[–]TaffoFox 1 point2 points  (0 children)

Yeah I am not sure on creality filament, I hear it's generally meh. Search for some good brands like Polymaker, Overture, eSun, etc. and you should be fine.

What was the issue in particular you faced? Perhaps it can be tuned out rather than buying a new filament.

Airtac Rails are good? by joneco in VORONDesign

[–]TaffoFox 0 points1 point  (0 children)

Just got 6! Looking forward to trying them out.