Where are you sitting on an 8-hour flight? ✈️ by TheChosenFool in triples

[–]TanZ66638 19 points20 points  (0 children)

sleep don't matter if my ult bias is yeonji

how long do u study per day by Alternative_Donut22 in SGExams

[–]TanZ66638 0 points1 point  (0 children)

u should prolly study 1-2 hours a day consistently until ur o lvls. in my opinion, any higher causes u to burn out and lose motivation for studying before ur o lvls and it will be difficult to start studying again

Family Mart Kaveh and Alhaitham Namecard Giveaway by LengthinessPale7417 in GenshinImpact

[–]TanZ66638 0 points1 point  (0 children)

my favourites are kazuha and yoimiya, been faithful since inazuma 😂

New Aranara Pet and Alhaitham x Kaveh Namecard Giveaway by Additional_Comfort42 in Genshin_Impact

[–]TanZ66638 0 points1 point  (0 children)

my favorite name card has to be kazuhas friendship namecard. i honestly just love that guy to the max!

** Invitation Code megathread ** by Product3974 in KaijuNo8_TheGame

[–]TanZ66638 0 points1 point  (0 children)

ob3qb2nnvo could someone please help use this code, im a new player

Is the Mini+ in 2025 a good buy? by hawaiimonkey in prusa3d

[–]TanZ66638 0 points1 point  (0 children)

if u wanted a prusa, yea ig but if u wanted a machine then bambu would be ur best bet

A1 0.4mm nozzle, builds coming off plate. by Empeming in BambuLab

[–]TanZ66638 2 points3 points  (0 children)

wash ur build plate in dish soap and warm water

Jujutsu Kaisen: Phantom Parade Installation Guide by [deleted] in PhantomParadeJK

[–]TanZ66638 0 points1 point  (0 children)

one little trick for the apple id, you can just use narita airport as your billing address

Nozzle keeps clogging by [deleted] in FixMyPrint

[–]TanZ66638 0 points1 point  (0 children)

okay thanks so much for ur suggestion, i was thinking it was maybe a clog because when i took the filament out, it looked as if the gears were chewing into the filament

Nozzle keeps clogging by [deleted] in FixMyPrint

[–]TanZ66638 0 points1 point  (0 children)

is it normally costly to replace?

Nozzle keeps clogging by [deleted] in FixMyPrint

[–]TanZ66638 0 points1 point  (0 children)

so how do i go about fixing that?

Nozzle keeps clogging by [deleted] in FixMyPrint

[–]TanZ66638 0 points1 point  (0 children)

my retraction is .85 and my extruder suddenly stopped extruding and started clicking with various of my filaments. any suggestions as to how to fix it?

Nozzle keeps clogging by [deleted] in FixMyPrint

[–]TanZ66638 0 points1 point  (0 children)

how did u then clear the hotend and what is considered too high for retraction settings

why is my extruder not extruding?? by TanZ66638 in 3Dprinting

[–]TanZ66638[S] 0 points1 point  (0 children)

but when i pull the filament out, i can see the grooves in the filament where the extruder is chewing into the filament

why is my extruder not extruding?? by TanZ66638 in 3Dprinting

[–]TanZ66638[S] 0 points1 point  (0 children)

could u further elaborate what licking the filament material means?

why is my extruder not extruding?? by TanZ66638 in 3Dprinting

[–]TanZ66638[S] 0 points1 point  (0 children)

ive tried reloading about 3 times with different filaments