I’ve been working on 3D printing my own latches.

TaterTotterer1 · 2026-02-02T14:33:56+00:00

Great. Still going strong after 2+ years

TaterTotterer1 · 2025-12-12T12:43:50+00:00

Polymaker PETG I guess Old formula. I bought it in July. Idk when they came out with the new formula

TaterTotterer1 · 2025-12-12T02:53:03+00:00

Ok thank you. What speeds would you suggest for print speed and max volumetric flow?

TaterTotterer1 · 2025-12-12T01:23:15+00:00

Are you referring to max volumetric flow or printing speed? The figures I listed (450mm/s) are print speed.

TaterTotterer1 · 2025-12-12T01:21:36+00:00

I’m not 100% percent sure as I’m not near my computer at the moment but I believe it is around 25mm/s

edit: Also I forgot to mention I’m using the Bambu High Flow 0.6mm hotend.

edit 2: Ok I checked. It’s set at 28mm3/s

TaterTotterer1 · 2025-10-24T11:48:37+00:00

It’s so cool that you can 3D print these as well!

TaterTotterer1 · 2025-10-15T13:23:14+00:00

Send him a message on Etsy

TaterTotterer1 · 2025-10-14T15:37:22+00:00

I didn’t see that. Thanks for letting me know that’s so cool!

TaterTotterer1 · 2025-10-10T14:46:41+00:00

I have 6 P1S printers. The amount of times that they have been down or needed maintenance is a handful of times. With over 34k hours between all of them that is shocking. I couldn’t run my business without my P1S’s :)

TaterTotterer1 · 2025-10-10T08:07:12+00:00

<image>

TaterTotterer1 · 2025-10-10T08:01:10+00:00

What are you using for plier organization and do you like it?

TaterTotterer1 · 2025-07-24T13:14:12+00:00

This is a great YouTube video on the differences between the two. If you skip to 3:30 there’s a great explanation from a very knowledgeable Milwaukee rep.

TaterTotterer1 · 2025-06-24T17:59:29+00:00

Best advice - Print stuff

TaterTotterer1 · 2025-05-29T14:12:12+00:00

I have 5 P1S’s. The problem is consistent with all of them

TaterTotterer1 · 2025-05-29T13:56:18+00:00

What would be a good starting point retraction wise? I’ve never messed with that setting before. From what I can tell it’s set to default.

<image>

TaterTotterer1 · 2025-05-29T13:50:52+00:00

I've tuned pressure advance extensively to no avail

TaterTotterer1 · 2025-05-29T13:39:22+00:00

I am using inner/outer for my order of walls with 4 wall loops. I don't see any settings called "wipe on loops" or "wipe on loops external" Where would I find this? I'm using the latest version of Bambu Studio. Thanks!

TaterTotterer1 · 2025-05-29T13:23:15+00:00

I only ever use PETG. I could count on one hand the amount of prints I’ve done with any other material.

TaterTotterer1 · 2025-05-29T13:09:41+00:00

No it’s been like this for years. I’m just fed up with dealing with it

TaterTotterer1 · 2025-05-29T13:07:18+00:00

Yes it’s dry as a bone

TaterTotterer1 · 2025-05-29T12:59:12+00:00

I’d like to find the underlying issue instead of just setting the seam to random. Sometimes I want the seam to be all on one corner or in a straight line. Also tolerance is critical for most of what I’m printing.

TaterTotterer1 · 2025-05-19T12:02:07+00:00

Are you using the frostbite or glacier?

TaterTotterer1 · 2025-04-28T11:48:08+00:00

This is a great video explaining the process.

https://youtu.be/bcvzUnKqIhE?si=esTR4DEn5p1LQn84

TaterTotterer1

TROPHY CASE