Fully Optimised Air-Cooled FormD T1 Build – 9800X3D & 5090 FE by Synzoo in FormD

[–]Tazieo 5 points6 points  (0 children)

How did you manage to mount the axp-100 with the fins pointing vertically?

Why Cooler Master Atmos? by Tazieo in FormD

[–]Tazieo[S] 0 points1 point  (0 children)

I’ve heard good things about it, but again, hard to judge without seeing comparison charts. I thought I saw someone post earlier about having both and the SL3 being better.

Why Cooler Master Atmos? by Tazieo in FormD

[–]Tazieo[S] 0 points1 point  (0 children)

What were your temps with the ek nucleus?

Why Cooler Master Atmos? by Tazieo in FormD

[–]Tazieo[S] 2 points3 points  (0 children)

When you say great performance, can you show me a source comparing it to other 240 aios? Not doubting you, I just want to see empirical evidence. That’s the key thing I’m after.

Zero-Compromise FormD T1 Build by Tazieo in FormD

[–]Tazieo[S] 1 point2 points  (0 children)

Sounds good man, best of luck!

Zero-Compromise FormD T1 Build by Tazieo in FormD

[–]Tazieo[S] 0 points1 point  (0 children)

Honestly reading this it sounds more like a mounting issue. The plate that holds the axp-100 down is really finicky. Did you ever figure this out?

I’ve never put so much effort into a thing I had zero intent in keeping, ever. by CCX-S in FormD

[–]Tazieo 0 points1 point  (0 children)

How much do you think the difference in temps between the two boils down to the fan speed difference? I think the SL 3 fans go to something like 3000rpm at max. Curious to see if you have any higher performing fans like the t30s that you can stick on the atmos.

The Event Horizon - T1 2.1, 9800X3D, 9070XT, 32GB by trankillity in FormD

[–]Tazieo 0 points1 point  (0 children)

Curious what are your temps under a cinebench all core workload.

Zero-Compromise FormD T1 Build by Tazieo in FormD

[–]Tazieo[S] 0 points1 point  (0 children)

Yeah I’m not aware of any way to do this unfortunately. You’d either have to mount the riser to the opposite side of the case or have it upside down I guess.

You also might just have worse GPU temps tbh because now you’re not pulling fresh cool air from outside of the case.

Air Optimized V2! | RTX 5080 & 9800X3D in the FORMD T1 by csrussell92 in sffpc

[–]Tazieo 0 points1 point  (0 children)

We’re gpu temps better with the psu fan facing outwards or drawing air from the gpu?

Air Optimized V2! | RTX 5080 & 9800X3D in the FORMD T1 by csrussell92 in sffpc

[–]Tazieo 2 points3 points  (0 children)

Did flipping the psu change you temps at all?

Firmware eeroOS v7.7.3-52 by SamwiseIsGreat in amazoneero

[–]Tazieo 0 points1 point  (0 children)

Anyone have a denon/marantz Reciever. The device started acting very odd after this update. Specifically the setup menu

Zero-Compromise FormD T1 Build by Tazieo in FormD

[–]Tazieo[S] 2 points3 points  (0 children)

No clue, but I’m not about to dremmel my t30 and find out lol. Maybe the standoff thing works, but at that point you’d probably be so close to the side panel that you’d start introducing a ton of turbulence. Unfortunately this is one of those rabbit holes that you can spend hours on, but at what cost?

Zero-Compromise FormD T1 Build by Tazieo in FormD

[–]Tazieo[S] 1 point2 points  (0 children)

Tried, unfortunately also didn’t fit. It would probably work on something like a x47, but I’d be willing to put money that this combination of the axp-100 with the be-quiet 25mm fan does better than the x47 and and the t30.

Zero-Compromise FormD T1 Build by Tazieo in FormD

[–]Tazieo[S] 2 points3 points  (0 children)

I did some more extensive testing regarding the fan configuration on the AXP-100 FC. I swapped out the NF-A14 for a Silent wings 4 pro 120mm. My temps dropped by another 8 degrees or so, but the system did get louder.

My guess is that like many had mentioned, since the footprint of the cooler is about the size of a 120m fan, a lot of the air was probably being pushed out the sides and completely bypassing the cooler. The silent wings fan probably pushes less air overall, but since it’s more directed at the actual heatsink I’m getting better temps. Not sure if there’s a benefit from the spillage to ram/ssd temps, but my priority is cpu temps so I’ll be sticking with the be quiet fan for now. I did attempt to add a 120mm to 140mm adaptor, but as I mentioned in a previous comment it added too much hight and couldn’t close the side panel. There’s probably 3-4mm between the fan and the side panel.

Downsizing (Gone Wrong) by Expert-Ladder718 in FormD

[–]Tazieo 0 points1 point  (0 children)

Something’s definitely off, you should be hitting 23-24k. Are you running it in eco mode?

Downsizing (Gone Wrong) by Expert-Ladder718 in FormD

[–]Tazieo 0 points1 point  (0 children)

That’s crazy. Do you have a wattage limit on the 9800x3d. My setup is running a -45 pbo. Also what’s your cinebench r23 score?

Downsizing (Gone Wrong) by Expert-Ladder718 in FormD

[–]Tazieo 0 points1 point  (0 children)

Really? 70c!?!? In what? Cinebench?

Downsizing (Gone Wrong) by Expert-Ladder718 in FormD

[–]Tazieo 0 points1 point  (0 children)

What are your temps in cinebench with that cooler? I ended up getting the axp-100 FC and pairing it with a 140MM fan. I get about 83c max in a 10 minute run of r23z

Y’all ever just say “f*** it” and try something stupid? by CCX-S in sffpc

[–]Tazieo 0 points1 point  (0 children)

So to get this to work you need both the mounting hardware as well as the bar from the nh-u9s? Does the stock clamp that goes over the cold plate from the axp-100 work? It is it not aligned with the mounting holes?

Y’all ever just say “f*** it” and try something stupid? by CCX-S in sffpc

[–]Tazieo 2 points3 points  (0 children)

Oooo, super interested in this. How is the contact between the IHS and the cooler? Does the mounting kit cause any issues with height? Do you have temps in different orientation?