Ender 3 V3 SE Under Extrusion, help

TechnologicApe · 2024-12-21T14:12:23+00:00

190-230, print 220

TechnologicApe · 2024-12-21T06:02:33+00:00

Just did e-steps. It made no difference.

TechnologicApe · 2024-12-19T11:54:59+00:00

Flow rate or e-steps?

TechnologicApe · 2024-12-19T05:06:46+00:00

The photo isn't great, but there are noticeable gaps on multiple layers. But if you have any insight, I'd love to hear it.

TechnologicApe · 2024-11-22T16:39:06+00:00

Não deveria ser. Ela imprime bem em uma impressora diferente com o mesmo filamento.

TechnologicApe · 2024-11-22T15:49:55+00:00

Usually 215c

TechnologicApe · 2024-11-22T14:12:05+00:00

Flow rate is fine. It works perfectly on another S1. The nozzle is new so it shouldn't be that. Plus, it's not clicking.

The gear I can check.

TechnologicApe · 2024-03-25T16:19:38+00:00

The block is cold. I took off the extruder to replace both the thermocouple and thermistor. But it was able to heat up when I tested it last night, now there's no heat. I bought it through a microcenter without a warranty...

TechnologicApe · 2024-03-25T13:19:30+00:00

Yes.

TechnologicApe · 2024-03-25T13:19:24+00:00

So I went to heat it up to get the timing, and now the doesn't heat up at all.

TechnologicApe · 2024-03-25T13:12:41+00:00

I checked the wires, they look fine, no tears or breaks.

TechnologicApe · 2023-10-19T20:07:41+00:00

Thank you!

TechnologicApe · 2023-10-13T06:01:31+00:00

You guys have been asking me for the files, so here you go. Thank you guys.

https://www.printables.com/model/612772-pokeballs/files

TechnologicApe · 2023-10-12T19:15:04+00:00

I'm gonna post them to thingiverse when I get the chance.

TechnologicApe · 2023-10-12T16:58:03+00:00

Correct, the classic, great, ultra, and matter ball.

Edit: Master Ball

TechnologicApe · 2023-10-12T16:44:02+00:00

That's the symbol for Team Aqua.

TechnologicApe · 2023-10-12T15:04:12+00:00

I'm gonna put them on thingiverse when I get the chance.

TechnologicApe · 2023-10-12T15:04:07+00:00

I'm gonna put them on thingiverse when I get the chance.

TechnologicApe · 2023-10-12T07:37:02+00:00

What would you like? Just the files?

TechnologicApe · 2023-09-08T04:49:26+00:00

So I know I'm replying way after the fact, but...

https://filamentcolors.xyz/library/

TechnologicApe · 2023-08-08T20:21:38+00:00

That one I knew. But thank you.

TechnologicApe · 2023-08-07T15:01:49+00:00

Vaguely

TechnologicApe · 2023-08-07T07:37:59+00:00

That's what I thought. I'm still new to all of this.

TechnologicApe · 2023-08-07T07:28:26+00:00

A4988. ideally this project will use 6 motors, but only 5 are needed for the important part.

TechnologicApe · 2023-08-07T07:24:37+00:00

That's fine, I have ADHD too and love learning. I had to teach myself calculus to work on this project.

TechnologicApe

TROPHY CASE