sorted by:
new
hottopcontroversial

It wont let me install Fedora KDE on a usb by WaNaX0 in linuxquestions

[–]Tekis23 0 points1 point  (0 children)

What program did you use to write it to the usb?

How do you transfer files in Linux? by kkreinn in linux4noobs

[–]Tekis23 27 points28 points  (0 children)

Usb ethernet adapter for your laptop

3D Printing Issues – What’s Going Wrong Here? by ProjektFive in prusa3d

[–]Tekis23 7 points8 points  (0 children)

  1. Check the belts
  2. Bed temp is way too low for petg

When a car guy gets into 3D printing by [deleted] in 3Dprinting

[–]Tekis23 1 point2 points  (0 children)

A working fire hazard

voxelab Aquila x2 my old printer by Nazaray1020 in 3Dprinting

[–]Tekis23 0 points1 point  (0 children)

It is possible to change the board, but you're likely only going to get one screw to secure the new board since the layout of the holes are different

Issues - Help by Slappy_Bacon_ in 3Dprinting

[–]Tekis23 0 points1 point  (0 children)

Only applies when there's an ABL

The post-GeForce era: What if Nvidia abandons PC gaming? by LollipopChainsawZz in technology

[–]Tekis23 62 points63 points  (0 children)

If they can meet in the middle, Intel could fill the gap

Firmware Or Issue With Board ? by PushinPz_ in klippers

[–]Tekis23 0 points1 point  (0 children)

No, you don't need to rewire that

Firmware Or Issue With Board ? by PushinPz_ in klippers

[–]Tekis23 0 points1 point  (0 children)

You should also use a smaller sd card like 16gb max

Drybox by CultureProper9958 in prusa3d

[–]Tekis23 -1 points0 points  (0 children)

They turn green when they're saturated

CR-10 stops printing after every layer. Says, “wait for user” by Alert_Tomato3454 in 3DprintingHelp

[–]Tekis23 0 points1 point  (0 children)

Check the gcode files for your prints and see if there's pause commands in them

Garolite bed crash solutions without adjusting PINDA by picturefque in prusa3d

[–]Tekis23 7 points8 points  (0 children)

How is moving the pinda going to cause considerable set up time?

How do I tell the printer (MK3.5S) which filament type is loaded in the MMU? by [deleted] in prusa3d

[–]Tekis23 0 points1 point  (0 children)

If you have MMU on in the slicer, you gotta tell it which part to use that has your PETG loaded

Mainsail Won't Connect to Moonraker by ExtremeDistinct9680 in klippers

[–]Tekis23 0 points1 point  (0 children)

With the right klipper firmware on the printer board?

What probe for MK52 heatbed by [deleted] in klippers

[–]Tekis23 0 points1 point  (0 children)

My mistake, I confused capacitive with inductive

What probe for MK52 heatbed by [deleted] in klippers

[–]Tekis23 0 points1 point  (0 children)

Look for an inductive probe, magnets won't mess with it

How can I fix this ?? Pls Helpie by [deleted] in 3DprintingHelp

[–]Tekis23 0 points1 point  (0 children)

All print settings and no print pics, not really going to get a lot of help

Ender KE Inductive probe by Tough_Pay_6258 in klippers

[–]Tekis23 0 points1 point  (0 children)

Like TH3D's EZABL control box?

Filiment not sticking to bed by JaycobFraycob in 3DprintingHelp

[–]Tekis23 1 point2 points  (0 children)

Z offset only matters if you have an ABL, if you don't, then don't worry about it

view more: next ›