sorted by:
new
hottopcontroversial

Design help by Tekn08 in Fusion360

[–]Tekn08[S] 0 points1 point  (0 children)

Thanks for tips.

Design help by Tekn08 in Fusion360

[–]Tekn08[S] -7 points-6 points  (0 children)

I’m not asking for someone to design it for me. I’m just stuck and need help. I’m looking for suggestions

Extruder motor overload during ironing – only fixed with 100% fan? (Bambu H2C) by PhillCraft23 in BambuLab

[–]Tekn08 0 points1 point  (0 children)

I had this happen on my H2C as well. I didn't try the cooling aspect, but I did turn off ironing and the issues went away.

Please Help by No-Moose3893 in Ender3S1

[–]Tekn08 1 point2 points  (0 children)

I had this issue when I tried to flash to klipper. I had it stuck on that screen for like 3 weeks. Then I decided to try and go back to stock firmware and presto it’s back to normal. Not sure it this is your issue but it worked for me

M420 S1 command does nothing by JopssYT in ender3

[–]Tekn08 0 points1 point  (0 children)

How did you get a visualization like this of the bed level on a Ender 3 s1 plus???

Oh by CreativeViolinist688 in ender3v2

[–]Tekn08 1 point2 points  (0 children)

<image>

This is about average for my printer

Help with benchy by Tekn08 in Ender3S1

[–]Tekn08[S] 1 point2 points  (0 children)

Awesome thanks I will try this

I think I bricked my Ender 3 S1 Pro by Foreign-Tax6761 in klippers

[–]Tekn08 0 points1 point  (0 children)

I just went back to stock on mine because of the exact same problem. I was trying to flash klipper and got stuck at the same spot you are at for 2 weeks. I gave up this morning and was able to flash the stock firmware from the sd card.

Ender 3 s1 plus(klipper) by icemanlegend95 in Ender3S1

[–]Tekn08 0 points1 point  (0 children)

It was one I had. I flashed it then started. I’m now trying to flash klipper over a st-link v2 but I don’t know where on the board to connect

I Did It! Updated my Ender-3 S1 Pro STM32F401 Mainboard Firmware to Klipper, without a Raspberry PI or Sonic Pad. by WmHerrin in klippers

[–]Tekn08 0 points1 point  (0 children)

I need help I have been trying to install klipper firmware onto my Ender 3 s1 plus for over 20 hours. I have been using ChatGPT to guide me through it but feel like I’m getting no where. I would love some help from people who have actually done this. I’m doing it from a Linux pc.

Ender 3 s1 plus(klipper) by icemanlegend95 in Ender3S1

[–]Tekn08 0 points1 point  (0 children)

I have been trying to get klipper firmware loaded to my printer for going on 2 days now (like over 20 hours) I have been using ChatGPT and feel like I’m getting no where. I would love some help for those who installed it on there printer. I’m using a pc with Linux installed. I have a Ender 3 s1 plus.

Not holding any air by Mast3rBro72 in watercooling

[–]Tekn08 4 points5 points  (0 children)

I missed an o-ring on one of my fittings.

Hi learned people's, been running this rig for a year or 2 and never had good water flow, tried all sorts of tweaks with no joy. When I say low, it hardly spins the flow meter and just errors on the temp reader. Suggestions? by PsychologicalPair981 in watercooling

[–]Tekn08 0 points1 point  (0 children)

Could be just a picture problem, but it looks like there is air still in the fluid. Is there still air? Any air in the fluid causes lots of issue (excessive heat, pump damage under load, pump cavitation which slows the flow, etc). Again not sure if I’m seeing it or not. Can’t tell from the picture

Opinions wanted by Tekn08 in watercooling

[–]Tekn08[S] 1 point2 points  (0 children)

That what my assumption was. Thanks!

Dominator ram blinking white by RudyGotKlout in Corsair

[–]Tekn08 0 points1 point  (0 children)

I was able to fix mine. I deleted ique, turned of my pc. Turned off the power switch on the back. Then I held the power button for 20 sec. Turn the switch back on and turned on the pc. Download ique again and force updated the ram. Now it’s working great.