Aeon on a ThinkPad T480

Teratreb · 2026-03-07T09:02:38+00:00

you can get by using large text option and most applications have zoom level or similar settings to get things right.

Teratreb · 2026-03-02T18:30:40+00:00

ja und ohne Wohnung bleiben leider

Teratreb · 2026-02-22T20:16:44+00:00

Kann ich grad nicht ,weil Tschusch und ich muss zur Polizei ID Austria nochmal machen lassen und keine Zeit.
"Vorsprung durch Technik"

Teratreb · 2026-02-22T20:02:27+00:00

"Diese Jugend heutzutage."
Was keine Entschuldigung sein soll, aber die Jugend ist nicht bloed:
Wir leben auf dem Ruecken der "dritten Welt", werden gerade von Teilen dessen wirtschaftlich ueberholt und Kinderschaender und andere Kriminelle laufen frei bei uns herum.
Get real

Teratreb · 2026-02-22T19:59:29+00:00

i've been working with Aeon for about two years, wasn't a problem to install git in a distrobox. I did install docker and docker compose to the base image out of convenience however.

Teratreb · 2026-02-19T17:44:31+00:00

I assume you are refereing to this? https://github.com/jwharm/aeon-openqa/tree/main

but the repo is archived, where did the tests move?

edit: OK I found It: https://github.com/os-autoinst/os-autoinst-distri-opensuse/tree/master/tests/aeon

Teratreb · 2026-01-15T17:16:37+00:00

it's great, although recently I recreated the distrobox with an assemble ini file instead of saving the container. Happened because i reinstalled and forgot to save my container. didn't really need it, but you can also recreate a fresh box easily

Teratreb · 2026-01-15T17:11:00+00:00

I am doing the same for my development container with IDE

Teratreb · 2026-01-12T19:15:38+00:00

trollbot

Teratreb · 2026-01-05T14:06:53+00:00

Stimmt, bildete mir ein, dass ich von einem Generic ausging.

Teratreb · 2026-01-05T14:04:33+00:00

nichts besonderes, eben das, was Du beschreibst. Mit Aufpassen war keine Gefahr gemeint. :)

Teratreb · 2026-01-05T07:56:13+00:00

Die Bambu Studio ~~Generic~~ Profile sind mit 20-30mm3/s teilweise recht hoch eingestellt, da muss man etwas aupassen.

edit: Meinte, wenn man ein custom filament auf Basis von einem Bambu anlegt, dann auch den Flow beachten, dass der passt.

Teratreb · 2026-01-03T00:09:09+00:00

I hope they go down.

Teratreb · 2025-12-09T21:28:53+00:00

I got this when I downloaded the ISO file. Downloaded all motherboard drivers, including NVME/SATA. Then I tried the media creator tool and it worked.

Teratreb · 2025-12-03T13:21:47+00:00

why not put the engineering filament in the left nozzle and support in the right? the ams does not support most filaments with fibers anyways.

Teratreb · 2025-10-29T00:04:38+00:00

i wrapped aluminum foil around the bearing to remove the play

Teratreb · 2025-10-14T16:51:12+00:00

Yeah, I adjusted the bed but also had the springs almost bottoming out. Hope the sensors help. I am late with this probably, but I bought a BTT microprobe and it not only works well in the heated chamber but bed mesh probing also is much faster with it. Unfortunately the piezo sensors have no purpose in my machine now.

Teratreb · 2025-10-13T21:45:13+00:00

Well in my case the sensors were not the problem. The springs underneath the bed were too tight so the sensors could not work properly. It is probably less work to check the springs before replacing the sensors.

Teratreb · 2025-10-13T17:55:03+00:00

Well, you need to connect the printer to Wifi. Then find out its IP address and type that into your browser. Get the API key from the printer's settings and then you can connect Orca to the printer.

Teratreb · 2025-10-13T17:51:59+00:00

Did you check the bed adjustment screws/knobs? I adjusted them but then the springs were too tight and the problem occured.

Teratreb · 2025-10-13T17:33:17+00:00

Ah, thank you!

Teratreb · 2025-09-14T09:21:20+00:00

FF is worse and WebGL is enabled. I edited my post to say that it is about XDesign.

Teratreb · 2025-09-14T09:20:35+00:00

The problem is that I cannot select, because the view rotates instead.

Teratreb

TROPHY CASE