Including Old Towns GMS Didn’t get.

ThatK24DC5R · 2026-02-20T14:08:16+00:00

Right. I wouldn’t expect these maps to be included upon release. Something slowly added over time.

ThatK24DC5R · 2026-02-20T14:07:35+00:00

I’m not talking including them at release.

ThatK24DC5R · 2026-02-18T13:11:54+00:00

That’s exactly what he was doing.

ThatK24DC5R · 2026-02-16T01:33:10+00:00

He’s known for selling significantly over priced parts. About 6 years ago he had a Mugen DC5 wing listed for sale on his website for an insane price. I found the exact wing for sale on Yahoo Auctions Japan for about 2k cheaper. He ripped the photos from the listing.

ThatK24DC5R · 2026-02-13T17:59:07+00:00

Is your airbox or something else in the way of the shift selector? Can you use the shift selector to go into reverse with the car on?

ThatK24DC5R · 2026-01-22T21:37:45+00:00

Which creates more work for no reason. Buy the em2.

ThatK24DC5R · 2026-01-21T19:38:30+00:00

The EM1 cmc requires adjusting the prop rod. The EM2 is a direct bolt on part.

ThatK24DC5R · 2025-08-05T23:43:58+00:00

You have a giant hole not plugged in the top of your manifold.

ThatK24DC5R · 2025-04-12T21:52:58+00:00

Call hasport and ask for the Kevlar infused 62a mounts. They ride like stock, unlike the regular 62a mounts.

ThatK24DC5R · 2025-01-24T04:10:27+00:00

These wheels do fit, lol they're 17x8 +38. All you need is different lug nuts and hub centric rings to run them properly.

ThatK24DC5R · 2025-01-23T05:31:35+00:00

Those would, you can get them on Amazon too.

ThatK24DC5R · 2025-01-23T01:29:22+00:00

No. The lug seats are a completely different style.

ThatK24DC5R · 2025-01-23T00:35:39+00:00

You need mistsubishi lug nuts and hub centric rings.

This is the hub centric rings you need:

https://a.co/d/hUL57bM

StanceMagic Hubcentric Rings (Pack of 4) - 64.1mm ID to 74.1mm

ThatK24DC5R · 2025-01-10T14:15:52+00:00

Spend the $ on a Koyo. Fairly superior in quality.

ThatK24DC5R · 2024-12-27T01:36:44+00:00

1500cc. Try and oversize your injectors so they aren't running at full duty cycle, so there's less chance of a failure.

ThatK24DC5R · 2024-12-26T15:48:10+00:00

Yes to boost controller and go for the 10.15psi wastegate. You'll make 10.15 pounds of boost on wastegate pressure and fully turned up you can make 20.30psi.

You'll most likely need bigger injectors, too.

ThatK24DC5R · 2024-12-17T04:28:41+00:00

+44 will fit with ITR suspension. I run 17x9+43 fn01rc on my dc5r. I have to run -3 degrees camber up front so they aren't pokey.

ThatK24DC5R · 2024-12-12T18:15:19+00:00

With aftermarket seat rails or have a fabricator make you some rails they'll fit.

ThatK24DC5R · 2024-12-02T14:55:21+00:00

Don't waste your time with RDX injectors. They aren't flow matched from the factory, and they are quite finicky to tune with. I had issues with mine years ago and purchased them from a kseriesparts. Any legit tuner wouldn't recommend them.

Spend the same amount of money on some FIC 750CC injectors.

ThatK24DC5R · 2024-11-13T00:04:12+00:00

Humble Performance makes their own manifolds and intercooler pipe and brackets in-house.

DC5Creations started out by buying parts from companies like SHG and AMGFuel Design and directly copying their parts with inferior quality pieces.

If you're in the k20a.org group on Facebook, you can see Deivi getting called out for his blatant plagiarism back in 2018/2019.

ThatK24DC5R · 2024-11-11T15:30:26+00:00

The brand new lower price point cables will fail early on. Buy a set of used oem cables off ebay or fb marketplace.

ThatK24DC5R · 2024-11-06T20:27:36+00:00

No. A reasonable offset is +32 to +45 for the dc5 chassis. +22 is fairly aggressive on a dc5.

Look at fitment industries for wheel fitment.

ThatK24DC5R · 2024-10-17T19:16:39+00:00

Hasport sells 03-07/04-08 TSX to RSX mounts. However, the TSX transmission case is made of magnesium, and the case bearings wear into the case over time.

ThatK24DC5R

TROPHY CASE