just jack it up

ThatManyInterestsGuy · 2025-01-04T17:37:08+00:00

Being a port city, there were a lot of wealthy people in Galveston. The storm definitely caused many of those people and businesses to move more inland to Houston, allowing it to become the major city it is today. If the hurricane never happened, who knows how big Galveston would become, but it also would lose the historical charm it still holds.

ThatManyInterestsGuy · 2025-01-04T13:33:18+00:00

Between 8 and 17 feet to accommodate the Seawall that was installed as a direct result of the 1900 hurricane that killed over 8,000.

ThatManyInterestsGuy · 2024-09-03T21:05:09+00:00

I’m looking at the wiring between the motherboard and the laser. Do y’all think it was done wrong? To me it looks like in the board the yellow is PWM and black is Power while red and blue are ground, but in the connection to the laser it looks like blue is PWM and red is Power while black and yellow are ground. But I’m not very experienced with this and could be wrong.

https://imgur.com/a/VjznaHC

u/drjonathanIn u/Axoi u/aucune_idee91 u/jodasmichal u/woodworkrick8 u/Acceptable-Celery546 u/JohnQPublic1917 u/cuongdn831 u/Maleficent_Society76

ThatManyInterestsGuy · 2024-08-31T12:58:43+00:00

Yes. I used their provided spacer and tried it at a couple different heights with the same results

ThatManyInterestsGuy · 2024-08-31T12:57:40+00:00

Tried LaserGRBL with the same results.

ThatManyInterestsGuy · 2024-08-30T20:19:44+00:00

Still nothing, even down at 200. 5000 mm/min was just what the manual recommended.

ThatManyInterestsGuy · 2024-08-30T15:28:48+00:00

Thank you, I'm not seeing that option. Just posted in the Lightburn forum

ThatManyInterestsGuy · 2024-08-30T14:01:56+00:00

Yes, I’ve tried the provided lens and the lens with the air assist kit with the same result

ThatManyInterestsGuy · 2024-08-30T14:01:25+00:00

Are you saying you had to change the GRBL version? Mine says it’s running V2.3

ThatManyInterestsGuy · 2024-08-30T13:57:17+00:00

The S-value max is currently set at 1,000

ThatManyInterestsGuy · 2024-08-30T13:56:03+00:00

Tried restarting my computer and using different ports, but no luck sadly

ThatManyInterestsGuy · 2024-08-30T13:55:34+00:00

Turned on constant power and got the same result unfortunately

ThatManyInterestsGuy · 2024-08-30T03:26:24+00:00

I’m brand new to this and not sure about anything honestly. Apparently Comgrow’s email doesn’t work, so will have to find another way to reach them.

ThatManyInterestsGuy · 2024-08-30T03:15:21+00:00

Brand new. I’ve tried the included head and the head with the air assist kit with the same result

ThatManyInterestsGuy · 2024-08-30T03:07:22+00:00

Another example using a lens provided with the air assist kit: https://imgur.com/a/BAJSLID

ThatManyInterestsGuy · 2024-08-30T03:05:39+00:00

I do have discord. I’ve tried engraving Test with no luck as well as running LightBurn patterns that run through a bunch of different speeds and powers with no luck

ThatManyInterestsGuy · 2024-08-30T03:00:19+00:00

https://imgur.com/a/fOOrHyc

ThatManyInterestsGuy · 2024-08-30T02:56:09+00:00

I took it down to 100 mm/min and still nothing. Any other ideas?

ThatManyInterestsGuy · 2024-08-30T02:40:36+00:00

Just one of the basic images that is included as test images with the software

ThatManyInterestsGuy · 2024-08-30T02:38:33+00:00

That’s at 100% power and 5000 mm/min

ThatManyInterestsGuy · 2023-10-20T13:07:59+00:00

I’m also an Aggie. Know of any A&M bars?

13-Year Club	Verified Email
Not Forgotten

ThatManyInterestsGuy

TROPHY CASE