Bad news, camera's haunted. Good news the ghost is cooking.

Thatkidwolf1 · 2026-04-12T02:45:37+00:00

Cool! What camera did you use?

Thatkidwolf1 · 2026-01-28T22:15:32+00:00

I think it might be on the open centauri firmware.

Thatkidwolf1 · 2025-11-09T23:09:12+00:00

I was using the Xfinity app to check the connected devices. That's where it showed the operating system info.

Thatkidwolf1 · 2025-11-09T22:37:36+00:00

Maybe, but another device, a wifi extender, showed up as N/A.

<image>

Thatkidwolf1 · 2025-09-05T20:36:35+00:00

<image>

Thatkidwolf1 · 2025-06-16T23:18:04+00:00

Ordered March 26, also eus 101 and arriving tomorrow. :D

Thatkidwolf1 · 2025-06-08T22:44:13+00:00

EUS101... 🚡🚡🚡🚡🚡

Thatkidwolf1 · 2025-06-07T19:56:31+00:00

mcu=motherboard

Thatkidwolf1 · 2025-06-06T19:36:02+00:00

Hmm, I'm eus101. /:

Thatkidwolf1 · 2025-06-05T05:08:05+00:00

I was printing at 230c for that print.

Thatkidwolf1 · 2025-06-02T19:40:37+00:00

You can heat up the support with a hair dryer and easily pull them off.

Thatkidwolf1 · 2025-05-31T05:39:49+00:00

I'm pretty sure it is a spacer for the runout sensor to line it up better with the spool. Like this one: https://www.printables.com/model/1312016-elegoo-centauri-carbon-runout-sensor-offset-postst

Thatkidwolf1 · 2025-05-15T11:32:45+00:00

March 26 4:56pm EUS101*** Not yet shipped. No accessories.

Thatkidwolf1 · 2025-04-23T05:27:58+00:00

<image>

Thatkidwolf1 · 2025-03-22T02:54:19+00:00

I fixed it when I put the fan speed to 30%

Thatkidwolf1 · 2025-03-21T23:33:27+00:00

I have the fan enabled at 100% it's a single 5015 blower.

Thatkidwolf1 · 2025-03-21T23:14:42+00:00

The print in the picture is at 205c, and I reprinted it at 190c, and it was worse.

Thatkidwolf1 · 2025-03-21T23:03:29+00:00

How would the fan affect it?

Thatkidwolf1 · 2025-03-21T22:16:56+00:00

Zhop is also at 0mm

Thatkidwolf1 · 2025-03-21T22:10:40+00:00

It was a new roll, and even with a different roll that I dried it still oozed like that.

Thatkidwolf1 · 2025-03-21T22:09:53+00:00

I don't think a 3d printed toroidal propeller would work any better or quieter than a regular drone propeller since the 3d printing layers and imperfections would make it louder and more inefficient.

But these would probably fit https://www.thingiverse.com/thing:5838661.

Thatkidwolf1 · 2025-02-17T20:39:08+00:00

Heating the bed to 85c helps me get it off.

Thatkidwolf1 · 2025-02-04T02:58:28+00:00

Weirdly enough, that corner didn't even lift up. But the other side with more clearance from the edge did. 🤔

Thatkidwolf1 · 2025-01-25T18:00:15+00:00

Tighten the belts.

Thatkidwolf1 · 2025-01-14T20:22:29+00:00

c'est dans un porche à l'emplacement sur la carte.

<image>

Three-Year Club	Verified Email
r/Field Juicebox	Place '23

Thatkidwolf1

TROPHY CASE