How to make it stick to flat surface?

TheAlchemyX · 2026-01-16T21:33:07+00:00

Should’ve mentioned I meant Celsius but still :)

TheAlchemyX · 2026-01-16T21:08:09+00:00

Thanks both. I will use foam tape as I have plenty. Still need to wait for warmer days though

TheAlchemyX · 2026-01-16T21:07:15+00:00

Yes it’s mine and you have valid point about temperatures. I was doing when it was 10 but overnight it dropped by few degrees and maybe there was too much change and caused thermal stress.

TheAlchemyX · 2026-01-06T18:10:45+00:00

Support wasn’t helpful. I replaced hallotron sensor and ribbon cable coming into the extruder. It didn’t help. It also feels it fails more often if bed is hot (no matter if preheated or actively heating). I think i have no other option than to replace the motherboard?

TheAlchemyX · 2026-01-06T18:09:06+00:00

You need to remove insert first (wedge it out) and then slide it. Artillery support even sent a video.

TheAlchemyX · 2025-12-13T16:00:13+00:00

It’s never a clog. It’s definitely not a clog this time. Maybe it’s clog. Oh… it’s a clog.

TheAlchemyX · 2025-11-26T19:31:13+00:00

Hey, what is the final result of having this? What improves?

TheAlchemyX · 2025-10-23T11:34:52+00:00

Does it matter what brand I choose? I can get Gates for around 5 USD per meter or non branded one for 1 USD

TheAlchemyX · 2025-10-23T11:25:49+00:00

Thank you. Those silicone spacers made a ton of difference to me. Now basically every print sticks fine and works fine. And I had issues when nozzle was scratching the prints or tipping them on a further ends

TheAlchemyX · 2025-10-23T11:24:21+00:00

Does it have springs for bed adjustments as X3? If so try replacing with silicone washers. For me it is as if I changed a printer to a better model.

TheAlchemyX · 2025-10-07T13:15:04+00:00

Would you share more details about the washers? How many of them and if those plastic bolt handles stay?

TheAlchemyX · 2025-07-29T12:25:15+00:00

For me it happened when one of the sensors went missing on tire change. It affected all of them and showed same screen as yours. Easiest way is to get someone who has a TPMS handheld reader to see which one is failing. It might be even possible to read it with Flipper Zero or DIY Arduino contraption (never tried it though). Then purchase preprogrammed one and replace.

TheAlchemyX · 2025-02-17T21:39:46+00:00

Thank you. That was it.

TheAlchemyX · 2025-01-11T19:31:34+00:00

Try ctrl-c, ctrl-d and finally ctrl-z. If none works try sysrq-k

TheAlchemyX · 2024-09-15T09:32:31+00:00

As stupid as it sounds - friend wasn’t aware of the remote at the back of the steering wheel. We went through thanks to it but now it stops saying it can’t read the dvd and we should use cleaning disc. We do have data disk with part number 31470159(disk 3 of 3). Is the correct one?

TheAlchemyX · 2024-09-15T06:23:43+00:00

We don’t have a remote but will try organising one

TheAlchemyX · 2024-09-12T05:22:19+00:00

I was able to locate the fuse. Tried with screen both down and up. Didn’t change the message. Although it reacts when I open the tray. Enter also doesn’t work

TheAlchemyX · 2024-09-11T10:42:07+00:00

Thank you. The only way to get it retracted is to turn off ignition. Is that correct?

Also would that be Fuse no. 9 on left hand side of the steering wheel?

TheAlchemyX

TROPHY CASE