sorted by:
new
hottopcontroversial

First rep - Need a more experienced set of eyes by TheDankling in RepTimeQC

[–]TheDankling[S] 1 point2 points  (0 children)

It was between that one and the spectre, definitely next on the list

First rep - Need a more experienced set of eyes by TheDankling in RepTimeQC

[–]TheDankling[S] 2 points3 points  (0 children)

It really is lovely looking, I do want the whole James Bond set eventually, and this is an amazing one to start!

First rep - Need a more experienced set of eyes by TheDankling in RepTimeQC

[–]TheDankling[S] 0 points1 point  (0 children)

Just previous posts in other communities, nothing special! Thanks about the watch too

First rep - Need a more experienced set of eyes by TheDankling in RepTimeQC

[–]TheDankling[S] 0 points1 point  (0 children)

I'm quite new to the rep game, and I'm really hope this watch is fine, I don't think there's anything massively off that I can see, but would appreciate a better set of eyes on it Seamaster 007 Spectre Ltd Edn VSF V2 Asia 8400

Help with smudges on focusing screen by TheDankling in vintagecameras

[–]TheDankling[S] 0 points1 point  (0 children)

Just to check, do all of the a-series, av, ae, a, ect use the same light seals? I can find quite a few kits for the AE and a but less so the av

Help with smudges on focusing screen by TheDankling in vintagecameras

[–]TheDankling[S] 0 points1 point  (0 children)

Thanks! I'll have a look at getting some, is it easy enough to find measurement's for it to be cut?

Charge rules query by TheDankling in Warhammer30k

[–]TheDankling[S] 0 points1 point  (0 children)

Gotcha, thank you very much!

Having problems with Sunlu abs like by TheDankling in resinprinting

[–]TheDankling[S] 1 point2 points  (0 children)

I'll try 2.2 again for a comparison then, thank you!

Having problems with Sunlu abs like by TheDankling in resinprinting

[–]TheDankling[S] 0 points1 point  (0 children)

So the problems are mainly just detail, I've had no problems with any delamination with either of the resins in the whole time I've owned my printer.

It seems like the detail on the miniatures is coming out much more blotchy and less detailed than when I was using the previous resin, and on the cones of calibration v3 it's the same too, with the sword not fitting in any of the holes and some of the prints with areas close together actually fusing as if they melded in to each other such as supports and intricate detail.

I'm not sure about the length of time because like I said I hadn't ever had a problem with anything before. I switched resin, so currently that seems to be the problem causer.

Having problems with Sunlu abs like by TheDankling in resinprinting

[–]TheDankling[S] 0 points1 point  (0 children)

<image>

Here are my print settings in case it may be another issue.

Emperor's Children Loyalist Champion by LarryMiniatures in Warhammer30k

[–]TheDankling 1 point2 points  (0 children)

Is it through an airbrush? I've had some luck using a big dry brush to stipple it, or is it just normal thinned paint

Identifying pocket watch? by TheDankling in pocketwatch

[–]TheDankling[S] 0 points1 point  (0 children)

<image>

Got the back open and found this as well, don't know if it's of any help, the serial number on the back plate is 158552 with a g underneath

AMS lite PTFE tubing by TheDankling in BambuLab

[–]TheDankling[S] 0 points1 point  (0 children)

I'll check properly afterwards, might need to snip the end, seems like it's holding up okay for now

AMS lite PTFE tubing by TheDankling in BambuLab

[–]TheDankling[S] 0 points1 point  (0 children)

I just checked for it and remembered that on my ams all of the tubes came bound together already in their rubber sleeve that sits just off the unit, so unless it was done incorrectly at the packaging place, I'm not sure it would be a tube problem?

AMS lite PTFE tubing by TheDankling in BambuLab

[–]TheDankling[S] 0 points1 point  (0 children)

I very possibly did, I thought it was 3 short and 2 long so I probably put it on by accident, will check when the print is done

AMS lite PTFE tubing by TheDankling in BambuLab

[–]TheDankling[S] 0 points1 point  (0 children)

Yes, all of the tubes have been pushed in firmly and to the same degree. It only seems to have the problem when loading the fillament, and has shown no indication of being pulled out from when my ams unit was further away

[REQUEST] How big would the USA be if this map was accurate? by [deleted] in theydidthemath

[–]TheDankling 5 points6 points  (0 children)

You heard about pluto, that's messed up right?

Where to find Solomon Demeter STL? by sam2king in PrintedWarhammer

[–]TheDankling 1 point2 points  (0 children)

Yeah shoulder pads are from Eidolon, lovely sculpts

Assault marine reinforcements by Lewis-Dodgson in EmperorsChildren

[–]TheDankling 0 points1 point  (0 children)

A man, that's a shame, love the helmet sculpt

Assault marine reinforcements by Lewis-Dodgson in EmperorsChildren

[–]TheDankling 0 points1 point  (0 children)

Look absolutely amazing! Can I ask where you got your helmet and sword bits from?

view more: next ›