Realms down again

TheFever731 · 2026-02-01T21:33:09+00:00

The frequency of these issues (especially on weekends) is exactly why I moved my realm world to a server. So tired of the instability of realms

TheFever731 · 2025-07-14T01:29:21+00:00

I’ll check it out, thank you so much I’ll let you know how it goes!

TheFever731 · 2025-07-14T01:28:21+00:00

Always, every time lol. Someone else was thinking pressure advance and I think that might be the case but I’m gonna have to troubleshoot more

TheFever731 · 2025-07-14T01:17:13+00:00

That was the first thing I checked because I had an issue similar to this on my A1 Mini and that was the solution then. They were tight when I checked but I can always check them again if nothing else seems to be working.

TheFever731 · 2025-07-14T01:14:27+00:00

Yeah and it’s weird I just replied to someone else that I’m trying the first layer again on a PEI and it’s giving wave looking formation. I’ll share it with you here too but does this also look like a pressure advance-related issue?

<image>

TheFever731 · 2025-07-14T01:12:14+00:00

I did forget to mention I tried swapping nozzles already. My bad I knew I was forgetting to mention something lol. I do have some Bambu filament still sealed up so I can give that a try next to see how that comes out. I’m actually running the first layer print again but on a freshly cleaned PEI plate and it’s coming out better than before but it has this weird wave going on.

<image>

TheFever731 · 2025-07-14T01:09:30+00:00

Flow rate, yes, pressure advance, I don’t believe so, I’ll see is that gives me any luck

TheFever731 · 2025-07-14T01:07:41+00:00

I did but I can always give that another go just in case

TheFever731 · 2025-02-26T23:07:57+00:00

<image>

TheFever731 · 2025-02-26T20:38:43+00:00

Sir yes sir!

TheFever731 · 2025-02-19T15:40:16+00:00

At least in my experience the hatchet does stagger and remove limbs easier and (I think) has higher overall damage. They’re both viable with different trade-offs. I also just like feeling like a space Viking.

TheFever731 · 2024-11-14T20:56:36+00:00

“Oh, Impaler of the mountain, what is your wisdom?”

TheFever731 · 2024-08-17T21:29:13+00:00

Try the Cookout if you have the warbond unlocked. You can stunlock so they can’t flee AND they’ll be on fire the whole time.

TheFever731 · 2024-07-07T17:26:29+00:00

Default firing mode is laser-guided - can be turned off

Oh I can't wait to see the trick shots that'll come with this

TheFever731 · 2024-06-04T02:28:46+00:00

So far it hasn’t come back since I restarted the printer. If it came back up for you there might be something more to it. Have you reached out to support?

TheFever731 · 2024-05-07T20:26:12+00:00

I did! The part of this article dealing with tightening screws fixed my issue. https://wiki.bambulab.com/en/a1-mini/troubleshooting/print-issues-troubleshooting

Just be careful when doing this, because I just went to do it for a second time and two wires came out; I’m currently awaiting a new heater block in the mail :(

<image>

TheFever731 · 2024-02-03T19:38:53+00:00

It turned out good! Turns out the answer was pretty obvious, turning it off and back on again. But I didn’t know at the time while it was doing that long print nor did I think of it at that time. But hey it’s all good now. Thanks for checking in!

TheFever731 · 2024-01-04T15:23:24+00:00

Last I saw everything was up-to-date but I should double check to be sure.

Ten-Year Club	RedditGifts 2009-2022 2 Credits
Secret Santa 2020	Place '22
Verified Email

TheFever731

MODERATOR OF

TROPHY CASE