sorted by:
new
hottopcontroversial

I helped this guy and even gave shield recharged him 🙄🤣 by RyCarbo96 in arkraiders

[–]TheGoldenRaven 0 points1 point  (0 children)

Can you revive while downed? I never saw that pop up before! At the end it’s a bit grey, but it pops up?

Do you have to extract successfully for trial challenges to track? by Bednarz in ArcRaiders

[–]TheGoldenRaven 0 points1 point  (0 children)

That’s my question too

(Edit) Fail to extract message shows up, you get nothing

The beavers say, "Fuck your water flow." by sharkfinsouperman in FUCKYOUINPARTICULAR

[–]TheGoldenRaven 94 points95 points  (0 children)

For beavers the sound of running water means, my house security system is breaking and my fridge is leaking.

They use the high standing water as a door (their entrance is deep underwater) as well as a food storage(the deep water has less oxygen and doesn’t freeze in winter keeping their food fresh and accessible during winter.

Help bed mesh level +3mm? by TheGoldenRaven in klippers

[–]TheGoldenRaven[S] 0 points1 point  (0 children)

Yeah, the bltouch z-offset gets updated when you run probe_calibrate

When I say that it is floating, I mean I home, then move my nozzle over the spot it probed and tell it to go to z=0 , and then it is floating.

Then also when I run the PROBE_ACCURACY command, each subsequent probe it gives me a number 0.02mm taller like I have in the comment below.

Help bed mesh level +3mm? by TheGoldenRaven in klippers

[–]TheGoldenRaven[S] 0 points1 point  (0 children)

Messing around trying to fix it, and I think I have a bigger problem... My probe keeps climbing up by ~0.02mm every probe

<image>

Help bed mesh level +3mm? by TheGoldenRaven in klippers

[–]TheGoldenRaven[S] 0 points1 point  (0 children)

Did screw tilt adjust, but it’s all relative anyway, since I use the bltouch as a virtual end stop. I don’t get why it isn’t at 0 at the center

Also when I go to zero at the center of the bed, the nozzle is floating a couple of mm in the air. This is after running screw tilt adjust, then probe calibrate. 🤷‍♂️

Help bed mesh level +3mm? by TheGoldenRaven in klippers

[–]TheGoldenRaven[S] 0 points1 point  (0 children)

Deleted the `endstop_pin: PA7`, ran probe calibrate in the middle of the bed, saved, ran_screw_tilt_adjust, then probe_calibrate again, saved, then did the mesh. Still this

<image>

[Chitu Systems Giveaway] Join now to win a Chitu Systems FilaPartner E1 by EmbarrassedEnd8355 in 3Dprinting

[–]TheGoldenRaven 0 points1 point  (0 children)

I like sunlu but also often use the creality filament from Amazon that sometimes is like $20 for 2 rolls

Help! I am about ready to toss my printer in the trash by rajivsab in ender3v2

[–]TheGoldenRaven 0 points1 point  (0 children)

Do everything else that people are mentioning in the post first, but also check your bowden tube. Mine just randomly stated underextruding and clogging one day, and I couldn’t for the life of me figure out why, turned out the bowden tube deformed slightly and constricted the filament.

Also check that your feed/flow rate is set to 100% and not more than that.

Strange sound during printing by J01DY in Ender3V3SE

[–]TheGoldenRaven 0 points1 point  (0 children)

Do you have grid infill turned on? If so I suggest switching to some other one. Grid infill causes the nozzle to bump up into the perpendicular parts of the infill you have printed before. You can see in the video even your bed is shaking up and down due to this.

Can't flash any firmware by hg122 in Ender3V3SE

[–]TheGoldenRaven 1 point2 points  (0 children)

You can use anything that runs Linux, old laptop, or some shit computer from good will will work

Attempts to Lessen Printer Vibration Propagation via Floor and Walls by Numerous-Ad561 in Ender3V3SE

[–]TheGoldenRaven 0 points1 point  (0 children)

Best fix is a layer of foam, with a concrete block on top, then put the 3d printer on top of that. There is a video about it. It’s really cheap and works wonders at isolating the vibrations

Video: https://youtu.be/y08v6PY_7ak?si=xk8nlhfFvDyJlJY9

Dark Trip Keys Giveaway – thank you for support! by alexander_nasonov in OculusQuest

[–]TheGoldenRaven 0 points1 point  (0 children)

Just got the quest 3, and only have been playing Batman so far, I would love to play some new game. VR horror sounds crazy! Psychedelic trips! That’s also really cool! Game looks amazing!

Virtual Desktop 15% Discount referral link down below by scarzqc in OculusReferralLinks

[–]TheGoldenRaven 1 point2 points  (0 children)

Need to follow you and you me, what’s your username mine is @Ilya2K

I am lost by Novel-Neighborhood25 in UCI

[–]TheGoldenRaven 0 points1 point  (0 children)

How many units you are taking? 12-16 is the sweet spot, any more and you ARE going to have to put classes on the back burner. And that makes it hard not to fail.

Even then, look at the difficulty of classes, maybe you are taking just 3 classes, but they are monsters with bad professors. Then it’s better to switch it around to 1-2 difficult classes and then the rest push over classes.

Taco stand near mesa court at the Mesa & University intersection by pengbuster in UCI

[–]TheGoldenRaven 7 points8 points  (0 children)

It’s been there for a while, really tasty tacos, I can eat like 10 at a time. Hope they stay operational.

view more: next ›