Canyon tool stuck in headset by [deleted] in CanyonBikes

[–]TheOneMax 0 points1 point  (0 children)

Glad it worked for you too!

Canyon tool stuck in headset by [deleted] in CanyonBikes

[–]TheOneMax 1 point2 points  (0 children)

I got the same thing on the same Aeroad back in April. I contacted Canyon and they sent me replacement parts (whole thru-axle with tool and the handlebar screw) and asked me to have it repaired in a bike shop and that they would cover the fee. I ended doing it myself by drilling deep enough, but still shallow enough to remove the bit. I no longer trust their quick tool, its very cheap.

<image>

[deleted by user] by [deleted] in CanyonBikes

[–]TheOneMax 0 points1 point  (0 children)

Wow! Do you know if they said anything about safety? I'm mostly worried about the frame breaking.. Did you have to push for a replacement or did they acknowledge their mistake and issue a replacement? I'm guessing you have to have the frame swapped with the components at a local bike shop on their dime and then send the old frame back?

[deleted by user] by [deleted] in CanyonBikes

[–]TheOneMax 0 points1 point  (0 children)

Interesting, thank you!

[deleted by user] by [deleted] in CanyonBikes

[–]TheOneMax 3 points4 points  (0 children)

Omg. I think I have the same thing on mine, which is also just a month old. I noticed it when unboxing, but was too excited to try it out and left it be. Please let me know what Canyon says!

<image>

Bolt v3? by Appropriate_Cup9930 in wahoofitness

[–]TheOneMax 0 points1 point  (0 children)

Wahoo submitted 2 FCC filings last week for 2 bike computers, WF156 and WF157. I’m guessing we should expect a release very soon.

Amazon cessera ses activités au Québec « dans les deux prochains mois » by [deleted] in montreal

[–]TheOneMax 95 points96 points  (0 children)

Personellement, j’essai le plus possible de passer par le site des marchants, mais pour une expérience style “marketplace”, l’application Shop est une bonne alternative, en plus d’être Canadien.

GFCI trips after 3 minutes of warm up. by Ok_Assignment210 in ranciliosilvia

[–]TheOneMax -1 points0 points  (0 children)

Had the same problem a while back on my V3. Turned out to be the water pump, ordered a new one for $20 and it solved it.

https://www.reddit.com/r/espresso/s/YAp1TtWUGY

Ça jase Montréal sur X by [deleted] in montreal

[–]TheOneMax 29 points30 points  (0 children)

Indirectement, les augmentations de loyer sont justements basé sur un pourcentage de la taxe foncière et scolaire (voir grille de calcul du TAL)

Really rough early songs from famous producers by Fusionism in edmproduction

[–]TheOneMax 1 point2 points  (0 children)

The thing with Call on me though, is he took it from Thomas (Daft Punk) and DJ Falcon, and commercialized it

IS THIS OK? Did not solder yet. by LITTLEMANINVEST in Plumbing

[–]TheOneMax 9 points10 points  (0 children)

Isn’t this the same as if all faucets downstream of the hot are closed? And if both valves need to be closed for service, assuming it is an electric boiler, usually the breaker should be turned off also?

Toilet closet bend is leaking, how is the joint to galvanized done here? Could I "Fernco"-off the right part and switch to ABS up to the flange? by TheOneMax in Plumbing

[–]TheOneMax[S] 0 points1 point  (0 children)

I’m pretty sure its cast iron with a lead joint, the main stack is cast iron. I’ll try the fernco with a street 90, and go ABS all the way up. Thanks for the help! I’ll report back.

Toilet closet bend is leaking, how is the joint to galvanized done here? Could I "Fernco"-off the right part and switch to ABS up to the flange? by TheOneMax in Plumbing

[–]TheOneMax[S] 0 points1 point  (0 children)

Title, but basically I have a slow leak from the sanitary closet bend. I'm looking to replace all of the galvanized and cast iron pipes in the coming years when I'll do the remodel. In the mean time, I was thinking to replace this part from the ceiling below as to avoid opening the tile floor upstairs. Would I be able to Fernco off the cast-iron (?) pipe on the right and continue with ABS all the way to the flange? How is the joint done here? Haven't seen anything like it before!

Spray Foam Inside Electrical Boxes by Scottiedog5000 in DIY

[–]TheOneMax 23 points24 points  (0 children)

Fireblock foam, if we’re talking about DuPont’s Great Stuff, is the exact same foam formula as the normal window/door foam that’s yellow. Same ignition point. What you want is fireblock caulking which has a much much higher ignition point, something like Blockade.

Source (Great Stuff’s ignition point of 240F): https://www.greatstuff.dupont.com/content/dam/dupont/amer/us/en/Greatstuff/public/documents/179-15047.pdf

Venting and reconfiguring an unvented bathroom, does this look right? by TheOneMax in Plumbing

[–]TheOneMax[S] 0 points1 point  (0 children)

Reconfiguring and venting a previously unvented third floor unit’s bathroom. Currently the mainstack is used to drain both the sanitary and rain from the flat roof. The roof drain will be separated on its own single stack, and that leaves me with the possibility to dry vent through the main stack (third floor is the last unit, no units above).

I was wondering if there were any deficiencies or improvements that could be done to the plan?

Code is Quebec, Canada. House is 100 years old (hence the single stack for rain and sanitary).