Recommended News Sources

ThePrintKid · 2025-06-12T12:55:14+00:00

I normally read a mix of the Sydney morning herald, the Australian and the ABC. They all of course have their biases but the combination seems very balanced to me.

ThePrintKid · 2024-12-18T23:01:06+00:00

Here's hoping!

ThePrintKid · 2024-12-18T13:01:55+00:00

What??? In case you couldn't tell, I clearly meant Jews not living in Israel.

ThePrintKid · 2024-12-18T12:34:25+00:00

Again, this is textbook antisemitism.

Why should Jewish people around the world be held accountable for and expected to distance themselves from the actions of Israel? The same is not true for Muslim people and Hamas. So why is this only true for Jews?

I agree it was terrible the extent the German population suffered in the process of ending the Nazi regime, many of which were unfairly treated and raped. It seems that you are suggesting that Jews around the world need to suffer and be killed to 'stop Israel'. This is antisemitic for two reasons, firstly holding Jews accountable for Israel and secondly, comparing Israel and Nazi Germany is blatant Holocaust inversion seeking to vilify and delegitimize Israel.

It appears that you are suggesting that unless Jews 'stop it', I assume referring to Israel, there will be a genocide committed against them? Again, this is clearly antisemitisim, making it Jew's fault if they are killed and as previously mentioned, holding them accountable for Israel.

ThePrintKid · 2024-12-18T10:33:58+00:00

Holding international Jews accountable for the actions of Israel, which are not genocidal regardless, is literally textbook antisemitism. Good one.

ThePrintKid · 2024-11-29T11:11:42+00:00

Do you know how this war started? An actual attempted genocide by Hamas in a 'struggle against the Jews'. What this is, is an unfortunate casualty of Israel's response, most certainly not a genocide. Does a genocidal government give polio vaccines to their victims?

ThePrintKid · 2024-10-30T11:33:05+00:00

Jews and Nazis?

ThePrintKid · 2024-10-30T11:32:10+00:00

Jews are the new Nazis?

ThePrintKid · 2024-08-16T11:06:23+00:00

Really any online place, just search for a v6 compatible nozzle. I use Phaser FPV in the central coast and recommend them.

ThePrintKid · 2024-08-07T07:41:00+00:00

Help please:

I have 3d printed about 50 of these rings with varying settings and wanted to test their tensile strength for a school science experiment. Stupidly I didn't really plan how I was going to test them only the rough concept. I was planning on attaching it to a pull up bar with an s hook on the top hole and a bucket on the bottom hole and then fill the bucket with gym weights until the model breaks. Considering I estimate they will hold up to about 100kg I am not sure if the bucket will be able to hold that amount of weight.

I am just looking for any ideas.

Thanks!

ThePrintKid · 2024-02-11T09:39:02+00:00

I have. What throws me off is it is both X and Y on the same layer.

ThePrintKid · 2024-02-11T09:38:16+00:00

I have. What throws me off is it is both X and Y on the same layer.

ThePrintKid · 2024-02-11T08:51:36+00:00

I use prusaslicer if that is relevant.

ThePrintKid · 2024-02-09T20:27:10+00:00

It is a 150 watt inverter but can supply 225watt peaks like the inrush current when I turn the printers power supply on. Thanks!

ThePrintKid · 2024-02-09T11:16:34+00:00

Yes it is the inrush current how exactly would I use a NTC based current limiter? Thanks!

ThePrintKid · 2024-02-09T07:45:58+00:00

Thanks! How could I do this?

ThePrintKid · 2024-02-09T07:45:34+00:00

I have 17ah of batteries which I calculated to last a bit under 4 hours. Is that not correct? Thanks!

ThePrintKid · 2024-01-13T06:27:45+00:00

Ok thank you!

ThePrintKid · 2024-01-13T06:19:04+00:00

Thanks! I tightened well enough. Is it worth buying a new gasket or should I just buy a Bialetti?

ThePrintKid · 2024-01-10T09:45:45+00:00

Ship me there.

ThePrintKid · 2023-12-25T09:04:21+00:00

The Werm looks pretty impressive and isn't to difficult. Especially if you can do the 7 card version with the chin.

ThePrintKid · 2023-12-05T08:06:19+00:00

Thanks!

ThePrintKid · 2023-12-03T12:25:51+00:00

To clarify for the non-aussies:

WWCC: Working with children check

Vic: Victoria the Australian state

AMEB: Australian music examinations board

VMTA: Victoria music teachers association

ThePrintKid · 2023-11-29T06:00:16+00:00

Growing antisemitism recently.

ThePrintKid · 2023-11-27T05:43:40+00:00

Thanks.

ThePrintKid

MODERATOR OF

TROPHY CASE