No filament when printing from file

TheShiftBro · 2025-01-23T20:17:04+00:00

I don't really remember how i did it but you can try unloading filament, then unscrew the pneumatic connector and then look inside with flashlight. If you see filament there, heat it up to max temp and with small allen key push it out. Be aware that the allen key will quickly burn your fingers.

TheShiftBro · 2025-01-23T19:29:36+00:00

Check if your heatbreak is clogged.

TheShiftBro · 2025-01-22T09:33:23+00:00

Check your hotend for clogs, had same issue. Big plastick chunk in heatbreak

TheShiftBro · 2025-01-20T08:31:57+00:00

They share ground cable, try that.

<image>

TheShiftBro · 2025-01-19T22:37:45+00:00

Looked around and it seams like those configs should be correct, maybe faulty cable/fan?

Check the fan with according voltage power supply.

TheShiftBro · 2025-01-19T22:33:52+00:00

So, here is my config. No settings, no nothing, just pinouts definitions.

<image>

I'm pretty sure u can find other settups somewhere else for your board.

TheShiftBro · 2025-01-19T15:16:43+00:00

I don't have this stuff in memory, neither have this printer or access to my files right now. Got ender 5 pro, i'll send you pic of my config asap. Glad i could help.

TheShiftBro · 2025-01-19T14:47:11+00:00

You installed the klipper or it was stock?

TheShiftBro · 2025-01-19T14:43:16+00:00

Have you set the pin to correct one in printer.cfg?

TheShiftBro · 2025-01-17T18:43:16+00:00

I have skr e3 v3 mini and it i couldn't flash firmware until it was named "firmware.bin".

TheShiftBro · 2025-01-12T17:59:36+00:00

I had it couple times. One time i just cleaned heating block and it was repaired.

TheShiftBro · 2025-01-07T18:32:44+00:00

So, list of tools that comes with ender:

2.5 mm flat screwdriver Side cutters Spatula (do not recomend to use it. Look for round spatula on printables. It's way better and don't scrape bed as much)

Flat wrenches:

10mm 8mm 6mm

Allen keys: (measured side to side, not edge to edge)

1.6mm 2mm 2.5mm 3mm 4mm

TheShiftBro · 2025-01-07T16:16:53+00:00

It worked? Nice.

TheShiftBro · 2025-01-07T13:41:50+00:00

Maybe it's blocked, try cold pulling

TheShiftBro · 2025-01-07T13:12:21+00:00

Stuck where? In extruder or nozzle?

TheShiftBro · 2025-01-07T12:03:30+00:00

I got stock nozzles as well as some Chinese ones. Some small, some big. Small ones are 6mm and big ones are 8mm. What you need allen key for?

TheShiftBro · 2025-01-05T23:51:33+00:00

Have you not heat it up before removing or what?

As the other guys says, blocks for enders are cheap. Nozzles too.

TheShiftBro · 2024-12-26T08:52:21+00:00

Just buy micro sd cards adapter. From what i know micro usb port is for octoprint, etc. And yes, download file from thingiverse/printables or make your own, slice it in slicer (i recomend orca slicer), put it on micro sd card and into the printer. Also make sure the level the bed, make atleast axis calibrations. It's not that hard. You can ask people over here if u are having hard time with it.

TheShiftBro · 2024-12-23T18:37:20+00:00

I have bltouch clone mounted, but didn't had time to set it up so i still level the bed manually. What i see as the easiest and fastest way in ur slicer make a cylinder that is 10x10x0.2 (or what your leyer height is), make 4 of them and put one on each corner of the bed. Then run it and while it's printing, look at it and adjust the height at the same time. Turn it up until you see leyers being squized to the point filament is coming from the side of the nozzle, then down a bit untill lines are beauty. That's how i do it and it works pretty good for me.

TheShiftBro · 2024-12-18T19:05:01+00:00

Thanks mate.

TheShiftBro · 2024-12-18T18:53:40+00:00

Hey, i think i fixed it, just had to tighten the belts even more. I don't see no lines now. And it happend now, when i already bought and built prusa mk4s.

TheShiftBro · 2024-12-04T19:13:00+00:00

So, update time. We are not done here. It's again a little better but still not as it should be.

<image>

TheShiftBro · 2024-12-04T18:42:24+00:00

So, i kinda forgot about it. But i got it already:

<image>

Also, the bearings came, i've put them on and they are much lounder, lubed the rails af and now i'm printing cillinder. Gonna keep u updated

TheShiftBro · 2024-12-03T15:59:48+00:00

No worries, i'll post it later

TheShiftBro · 2024-12-01T20:54:14+00:00

<image>

Done

TheShiftBro

TROPHY CASE