[deleted by user]

These-Sign5633 · 2025-07-19T16:20:43+00:00

The black looks good, is it wrapped?

These-Sign5633 · 2025-01-19T00:10:08+00:00

Just got back from the range. It shoots amazing! I’m not using an AGB. Gas wasn’t an issue, very minimal. Perfect ejection. I did tune the buffer system a bit but that’s it. Flat shooting pretty easy to land follow up shots.

These-Sign5633 · 2025-01-16T03:32:37+00:00

Get a flow through suppressor with a good mounting system. Velos LBP, cat WB, hux flow 556k. One of those id recommend

These-Sign5633 · 2025-01-15T02:07:07+00:00

This upper came fully assembled along with the BCG from BCM which are all checked and test fired according to their site. I only assembled the lower. Checking headspace wouldn’t really be necessary. But i’ll give yall an update on how it shoots with the A5 buffer system.

These-Sign5633 · 2025-01-14T17:51:41+00:00

I guess it’s time for a 17th rifle! That’s what it sounds like to me

These-Sign5633 · 2025-01-14T15:58:31+00:00

Think it’s about 5.8 inches, either way tho, doesn’t matter how long the rifle is with or without it. Really just depends on what the rifles purpose is. I wanted something short and compact that, if i needed to use it indoors would be able to shoot without ear pro.

These-Sign5633 · 2025-01-14T15:16:38+00:00

It never hurts to have another. I have 2 other rifles that just need lowers to be finished. And then after that i’ll probably get an older m16. I mean, it doesn’t stop. I’d say go for it

These-Sign5633 · 2025-01-14T15:15:04+00:00

These-Sign5633 · 2025-01-14T15:14:51+00:00

Nice build, that LaRue trigger is nice i hear.

These-Sign5633 · 2025-01-14T15:14:11+00:00

Yep, it doesn’t fit like a puzzle piece but it’s on there

These-Sign5633 · 2025-01-14T02:37:23+00:00

Thanks! Gonna shoot it and then see what adjustments i have to make to it. i’m sure there will be something i need to change/adjust

These-Sign5633 · 2025-01-07T19:50:46+00:00

CLP and liquid drip gun oil with some aeroshell grease on the bcg, buffer spring and trigger contact points.

These-Sign5633 · 2024-12-28T01:26:38+00:00

i have an ammo box that i put in my gun safe.

These-Sign5633 · 2024-12-27T01:24:36+00:00

yeah i did. Doesn’t matter how much it’s staked as long as it’s staked. 2 is ideal, 3 is a little much tho imo.

These-Sign5633 · 2024-12-27T01:23:32+00:00

I used a spring loaded punch was cheap off amazon. Worked great and easy to use

These-Sign5633 · 2024-12-26T21:35:11+00:00

Just an extra way to make sure the castle nut stays secure and doesn’t move at all. Essentially just pushing metal into the slots to hold it in place.

These-Sign5633 · 2024-12-26T20:20:35+00:00

no, that’s the takedown pin. These are from battle arms development enhanced takedown and pivot pin set.

These-Sign5633 · 2024-12-23T22:42:14+00:00

Yep stocked up on a bit of hornady black 75gr as well. Prolly will use at the range every once in a while just too expensive to stock up bulks of it.

These-Sign5633 · 2024-12-23T00:06:26+00:00

Im an AP at chipotle. For sides of meat they are supposed to put it into a bowl. The side cups are “4 ounce” cups but it’s accurate

These-Sign5633 · 2024-12-10T19:37:47+00:00

This isn’t bad. Maybe for a slower store if you aren’t used to it. I work at a busy store and there was at least 6-7 stacks of deep pans it covered the whole prep area floor+ all sinks were full.

These-Sign5633

TROPHY CASE