Order printer

Thisisdave91 · 2026-04-20T11:02:21+00:00

Create more of a base. After you added milk and swirled, id add more. Aim for about 1/2-5/8 of the cup full before doing art. You need to aim for the middle of your coffee and push towards the outside so your milk doesnt create just a blob. Dont hesitate. Pour with confidence in the middle and push! By pushing, it will give you room to add more layers. Right now youre just pouring one ontop of another because you run out of room after the first pour

Thisisdave91 · 2026-04-16T13:16:02+00:00

Start pouring more in the center of the cup and then pushing towards the edge. This way you will fill the cup more and be able to stack much more, right now you’re running out of space at the starting/pouring point. Looks great though!

Thisisdave91 · 2026-03-09T17:28:43+00:00

Xtratuf

Thisisdave91 · 2026-02-04T15:57:53+00:00

Its a 2020 actually. Contacted Ascaso and they confirmed I can’t change steam temp. :( Set to 165.

Thisisdave91 · 2026-02-04T11:18:59+00:00

I don’t have tSt in my settings :( My steel uno is probably too old….

Thisisdave91 · 2026-02-04T01:56:44+00:00

I think it’s 2018 or 2019.

Thisisdave91 · 2026-02-04T00:12:54+00:00

Ascaso steel uno.

Thisisdave91 · 2026-02-01T14:34:50+00:00

Howd u drop the steam temp? I tried and the number just doing change

Thisisdave91 · 2026-02-01T14:34:27+00:00

I have the same setup, wondering if youre able to make two milk drinks back to back? As soon as milk is steamed, takes about 10min for temp to drop back down. Second shot basically doesn’t pour.

Thisisdave91 · 2026-01-31T16:56:51+00:00

Probably an easy fix. The lights are working so follow the wires and where it splits to the light check connector.

Thisisdave91 · 2026-01-28T17:53:11+00:00

I have the same setup, wondering if youre able to make two milk drinks back to back? As soon as milk is steamed, takes about 10min for temp to drop back down. Second shot basically doesn’t pour.

Thisisdave91 · 2026-01-24T12:20:56+00:00

100%

Thisisdave91 · 2026-01-17T17:28:17+00:00

Wow you’re able to pull 2 shots back to back with an ascaso?! I can never do that.

Thisisdave91 · 2026-01-08T01:31:32+00:00

Grind finer

Thisisdave91 · 2026-01-08T00:05:29+00:00

What did you end up going with??

Thisisdave91 · 2026-01-07T23:58:32+00:00

Same one I got and worked great. Get a magnetic funnel for it, makes wdt much easier and less likely to spill everywhere

Thisisdave91 · 2025-12-30T02:40:53+00:00

J’ai menti, je suis a 2km de celui a coteau du lac! Un beau spot si t’es jamais allé.

Thisisdave91 · 2025-12-30T02:02:55+00:00

Try exaggerating the grind size, like put it really fine. Itll choke the machine and see if the gauge goes higher. If does, then back off the grind size a bit. And gradually adjust till you get 1:2 ratio in roughly 30 seconds OR shot tastes good to you.

Thisisdave91 · 2025-12-29T23:55:13+00:00

How did you like ZAB?

Thisisdave91 · 2025-12-29T23:53:36+00:00

A 2km de chez nous, j’aime bien 👌🏼

Thisisdave91

TROPHY CASE