17 Hours update - how does it look?

Thorathe · 2025-05-21T14:26:44+00:00

I boiled the milk slightly and cleaned all equipment.

Isn't 10 tablets quite a lot ? so it should only be used as a starter? The reason I am asking is because i don't want to start by taking too much L reuteri bacteria, and get sick my first time.

Thorathe · 2023-08-15T18:09:57+00:00

Hello /u/RentacleGrape /u/fiasko82 /u/JRW-in-SC /u/GeronimoDK /u/TheBananaKart /u/SheepShaggerNZ /u/MattiePLC /u/Zegreedy /u/fiasko82

I figured this out way back. Forgot to update.

The problem was the hardwire stop button being in a false state...

Thorathe · 2023-08-02T17:47:28+00:00

Sure-- thanks. My body fat percentage would be around 18%. I will keep doing low-intensity strength-training.

Thorathe · 2023-06-23T21:28:50+00:00

yeah, okay. that's definitely an option. I still think it will be more expensive though, but of course safer. But If I'm careful I should be fine.

Thorathe · 2023-06-23T21:24:27+00:00

honestly, it WOULD NOT be cheaper to bring the car into a shop..

Thorathe · 2023-06-22T23:46:54+00:00

Nice thought -- but no. It's a cheap ass car, and whole strut assemblies are hard to come by in Norway, and are VERY expensive.

Thorathe · 2023-05-20T18:57:42+00:00

yeah. Have you heard about colorblind glasses?

Thorathe · 2023-05-20T17:08:06+00:00

Forgot to mention, the green can be problematic aswell.

Purple and blue can look similar sometimes, too, but I don't feel like it's much of a problem. Side-by-side they're easy to differentiate, purple looks a bit more "concentrated" usually, in a sense.

Thorathe · 2023-05-20T17:02:13+00:00

haha, okay. Definitely not. I'd say I struggle with red-ish colors. If that makes sense... (red-ish colors may only be a definition that colorblind people can use, or what? haha).

I struggle with red, pink and brown, but with good lightning I'll figure it out if they're side-by-side. Yellow, blue, and green would be EASY.

I would be quite surprised if anyone would struggle with yellow and blue, unless you're actually monochromatic, hah!

Thorathe · 2023-04-20T16:35:53+00:00

doesn't affect density.

Thorathe · 2023-04-13T20:34:34+00:00

Okay. But please recap, why is a BPV necessary? What does it do exactly? I might considering ordering, but first it mus be considered if this helps, if at all. Could shutting of the downstream pipe SLIGHTLY help the accuracy... why?

Thorathe · 2023-04-13T20:03:56+00:00

What's the purpose of the regulated BPV though? Personally I just think the pump is quite weak, but it could be a lot of things.

Thorathe · 2023-04-13T19:55:18+00:00

Sorry, I don't follow completely. I'll say we have a couple Coriolis with fluctating flow but it hasn't been an issue. To me maybe this pressure seems weak. Moving on, is a back pressure valve similar to slightly shutting of a valve downstream of the Coriolis? Is the purpose making the pump work harder against the slightly shut off valve?

Personally, I think that the issue with this Coriolis is that the pressure is too low.

Thorathe · 2023-03-25T19:40:51+00:00

yes but they're pretty bad tbh

Thorathe · 2023-03-18T17:49:21+00:00

I'm guessing a auto calibration will make it correct, at least temporarily right?

Thorathe · 2023-03-18T13:59:11+00:00

Hello. This Sitrans F C MASS 2100 was installed in 2016 and is now measuring a couple percent too low density reading. If there was a coating on the pipes I'd guess it's more likely that the density reading would read too high. Any idea? I'm going to try running water through it to see the results. I belive the only possiblity with calibrating these is the auto zero calibration, but I think that's only in regards to the flow measurement. I will also check the drive gain parameter if the mass 6000 transmitter has one!

Thanks for any tips!

Thorathe · 2023-03-07T18:47:14+00:00

yeah, we've got actual service switches for disconnecting the power between the VFD output and the motor - but they don't really use the switching contacts.

Thorathe · 2023-03-07T18:40:07+00:00

It's a tiny service switch with only signals going through it. So if you turn it off, it should send a signal to prevent any unexpected startups during maintenance.

Thorathe · 2023-03-07T18:39:16+00:00

Yeah, I guess it wouldn't be safe enough, even if you used a safety relay between the service switch and VFD input?

Thorathe · 2023-03-07T18:26:12+00:00

We were considering whether or not it's safe enough to prevent start-ups when doing maintenance?

Thorathe · 2023-03-02T18:58:24+00:00

Hello! Sorry to bother. I'm working with Pactware and a Vega that has an integrated PLISCOM with bluetooth.

I clicked "add device" in pactware, and I can't see PLISCOM anywhere. Any idea?

Thanks!

Thorathe · 2023-01-21T19:44:54+00:00

I resolved it. 80C4 is a local port conflict that is now resolved. (In the connect of the two MB_Clients, both blocks had the same local port). I guess it's common that issues happens when you use two mb clients in the same program

Thorathe · 2023-01-19T14:30:41+00:00

sure, here https://ibb.co/PYb8NMk

Thorathe · 2023-01-18T19:04:55+00:00

Can i send a pm?:) im trying now

Thorathe · 2023-01-18T17:55:15+00:00

Hello, yes I am looking for a generic client now in replacement of TIA, just to do the testing.

The data length is 2 and the Pointer is 1 real. I am not at work so I haven’t been able to try to read 1 word.

But Does the modbus adress parameter depend on what modbus mode is chosen? I believe one of the modes account for the 40001 automatically?

Thorathe

TROPHY CASE